J&E Hall JEHSD-0400-B3-M-3 Скачать руководство пользователя страница 22

Страница: 22 / 44

Issue: 01.08.2020

Commissioning

Switch Unit ON / OFF (By Controller)

With controller Home screen displayed, Press PRG button to go Main Menu screen and select “A. On/Off Unit”

Press ENTER button. Screen A01 is displayed.

Press ENTER button to move cursor from home position to SWITCH OFF value. Switch Unit ON by using UP/DOWN
arrows. Press ENTER button to confirm.

Press ESC button repeatedly to return to Home Screen. This should now show ON by KEY at the bottom of the screen.

The unit will start up following a short delay (assuming all conditions for compressor start

Switch Unit ON / OFF (By Controller)

displayed, Press PRG button to go Main Menu screen and select “A. On/Off Unit”

Press ENTER button. Screen A01 is displayed.

Press ENTER button to move cursor from home position to SWITCH OFF value. Switch Unit ON by using UP/DOWN

ENTER button to confirm.

Press ESC button repeatedly to return to Home Screen. This should now show ON by KEY at the bottom of the screen.

The unit will start up following a short delay (assuming all conditions for compressor start-

Page 22

displayed, Press PRG button to go Main Menu screen and select “A. On/Off Unit”

Press ENTER button to move cursor from home position to SWITCH OFF value. Switch Unit ON by using UP/DOWN

Press ESC button repeatedly to return to Home Screen. This should now show ON by KEY at the bottom of the screen.

-up are met).

Содержание JEHSD-0400-B3-M-3













































Результаты поиска

Содержание JEHSD-0400-B3-M-3

Отзывы:

Похожие инструкции для JEHSD-0400-B3-M-3

Бренды по названию

Популярные бренды

J&E Hall JEHSD-0400-B3-M-3, Техническое руководство

Результаты поиска

Содержание JEHSD-0400-B3-M-3

Отзывы:

Похожие инструкции для JEHSD-0400-B3-M-3

Бренды по названию

Популярные бренды