background image

IO-11

Jade Range LLC 

– A Middleby Company

Titan

TM

 Series Heavy Duty Range

Model Series JTRH & JTRHE

Top Burner Adjustment

1.

Remove top burner control knobs.

2.

Remove front manifold cover plate

3.

Loosen the screw on the air shutter.

4.

Light the burners and observe the quality of
the flame. Flame should be sharp, well defined,
two-tone blue as shown in Figure 7(A).

5.

Adjust the air shutter as required.

6.

Tighten screw on the air shutter.

7.

Repeat procedure for all remaining burners.

8.

Replace front manifold cover plate once all
burners are properly adjusted.

9.

Replace burner knobs.

NOTE: 

When using LP (liquid petroleum/propane)

the flame may have a slight yellow tip, however
the yellow tip should be no greater than 10% the
overall flame size as shown in Figure 7(B).

Figure 9: Top Burner Air Shutter Adjustment

Oven, Griddle and Hot Top Burner
Adjustment (Tubular Type Burners)

1.

Remove kick plate (for oven). Remove front
manifold cover (for Griddle/Hot Tops).

2.

Loosen the screw on the air shutter.

3.

Light the burner and observe the quality of the
flame. Flame should be sharp, well defined,
two-tone blue as shown in Figure 7(A).

4.

Adjust the air shutter as required.

5.

Tighten the screw on the air shutter, replace
covers/knobs/panels as required.

NOTE: 

When using LP (liquid petroleum/propane)

the flame may have a slight yellow tip, however
the yellow tip should be no greater than 10% the
overall flame size as shown in Figure 7(B).

 

  

  

Figure 10: Tubular Burner Air Shutter

Adjustment

Содержание JTRH Series





















Отзывы: