INST 448 Jacuzzi® JVX Series Pool pump V10-17
11
OPERATION OF CONTROL PANEL (CONT…)
Setting pump to operate independently of external Compliant Chlorinator or Control System
1.
Toggle Menu until “CONF” is displayed on the LCD screen
2.
Press and HOLD “enter” for 3 seconds. “TMRS” will appear.
3.
Press “enter”
4.
Press UP or Down buttons to turn “TMRS ON”
5.
Press “enter” to accept
6.
Press
“auto” to return to main menu.
Changing Low, Med and High Speed Settings
1.
Select the Speed Button to be adjusted, Low, Medium or High. Respective LED will light up.
2.
Alter the speed in increments of 25 RPM using the up and down arrows until the desired speed is
displayed on the screen. Respective “Speed 1”, Speed 2” or “Speed 3”, will flash while editing. “Speed 3”
can be set to “Overdrive” mode if desired by using the up arrow to raise the speed above the normal
maximum speed. (In overdrive mode, the actual RPM isn’t displayed, instead a rotating symbol is
displayed)
3.
The new speed will automatically save after 2 seconds. Flashing will stop to signal save.
Setting filtration timer periods
1.
Press Menu to go to PRIM setting.
2.
Prime period is defaulted to 5 minutes and high speed. We recommend if your pump is installed at or
below water level, you change the PRIM to 2 minutes. Press “enter” and then Up or Down arrows to
change the prime speed. Press “enter” to accept. Priming period will now be displayed.
3.
Use the Up or Down arrow to change the Priming period. Press “enter” to accept.
4.
Press Menu to go to TMR “timer settings” and press “enter” to change.
5.
Timer 1 is factory set to start at 8 am. Use up or down arrows to change. Press High, Medium, or
Low to select the speed of the pump during Timer 1. On the LCD Screen High is represented by speed
“1”, medium by speed “2”, and Low by speed “3”.
6.
Press Enter to move to the stop or end time of Timer 1. Use the up and down arrows to change the
end of Timer 1.
7.
Timer 2 will now appear on the LCD Screen. Repeat instructions 4. to 6. Above.
8.
Timer 3 will now appear but is factory pre-set to OFF. Moving any timer to midnight will turn that
Timer period off. Use the up and down arrows to activate the time and repeat process 4 and 5 above.
9.
Timer 4 is also factory pre-set to “off” but can be activated by using the up and down arrows.
10.
Remember to select the speed you wish to operate during each timer period by pressing the High,
Medium or Low buttons while still in the Timer Start program.
Using the inbuilt pump timers with a non-compliant chlorinator or dosing unit.
1.
We do not recommend the use of the pump timers when a non-compliant chlorinator or chemical Dozer
is supplied water flow by the Jacuzzi® JVXP150 or JVX250 Pool Pump.
2.
In this case, the pump operating hours should be controlled by the chlorinator time clock and the pump
plugged into the chlorinator. This is a safety measure provided for by most chlorinator manufacturers.
3.
However, it is important to deactivate the inbuilt pump timers.
4.
Have Pump in “MANUAL OFF”
5.
Toggle Menu until “CONF” is displayed on the LCD screen
6.
Press and HOLD “enter” for 3 seconds
7.
Toggle Menu until “TMR” appears.
8.
Press UP or Down buttons to turn “TMR OFF”
9.
Press “ENTER” to accept
10.
Press
“AUTO” to return to main menu.
11.
When cycling through the Menu button TMR will no longer appear
12.
You will no longer be able to automatically have the speed of the pump changed during different times of
the day.
13.
However, if you wish for a period where the pump operates at a high speed, for example to circulate the
water vigorously for a part of the daily filtration, you can use the PRIMING setting to do so.
