Jacuzzi Sharp, Руководство по установке

Страница: 7 / 24

(part. 2) Fix the suction nozzle cover with o-ring using the
specific screw.
(part. 3) Pressure fit the flange cover on the whirlpool flange
cover.
(detail 4) Snap fit the lid on the spotlight body (optional).
Important: Keep the plastic conical tool (A) needed for
removing the hydromassage nozzles.
Insert the switch knob into place.
run a hydromassage cycle, making sure that there is no leak-
age, particularly in the hydraulic connections and drain.
InstallIng thE panEls
(where present)
Secure the metal elastic support/s (L) by means of the two self-
tapping screws to the small block (N) under the tub rim
( 8 ).
Click the springs (P) onto the legs located at the corners of the
tub and make them slide up until they touch the top, push-
ing them from both sides so that they settle inside the tub rim
(
9 ). Insert the ring (R) into the groove of the leg.
Insert the plastic supports (S) into the legs (Q) ( 10 ).
While maintaining the height of the tub from the floor (57 cm,
2 ) adjust the height of the plastic support (S) by means of
the ring nut (Y) according to the height indicated ( 10 )
.
To lock the plastic support (S), tighten the screw nut (X) by
means of a spanner , applying light force.
If side panels are to be installed, secure the plastic clips (T) on
the panel itself by means of the self-tapping screws (
11 ).
Use holes “1-2” to assemble the left panel and holes “3-4” for
the right panel.
Insert the side panel between the springs (P) and the tub rim
(
1
2 ). Lift it up until the clips (T) are aligned with the plas-
tic supports (S) and click it onto the supports themselves.
To adjust to a perfect right angle of the panels, use the screws
(V).
( 12 ) On the screws (U) apply the provided white caps.
WooD panEl assEmBly
(where present)
Follow the relevant assembly instructions.
assEmBly oF thE “l” shapED panEl
(where present)
( 13-13a ) Refer to the figure displayed for the assembly of
the “L” shaped panel.
FInIshIng touchEs
(
14 ) The very last step of installation consists in filling the
specific tank fixed to the metal frame of the tub with disin-
fectant.
( 15 ) Remove the protective film from the lower part of the
headrest (1). Position the headrest on the backrest (2).
Carefully apply silicone to all the rim, in the points that rest
against the wall (3). It is advisable to install Jacuzzi® finishing
parts, available on request (4).
gEnEral WarnIngs
JACUzzI EUROPE S.p.A. declines all responsibility in the fol-
lowing cases:
If installation is carried out by unqualified personnel and/or
personnel unauthorized to carry out installation.
If the norms and legal provisions, regarding the electric sys-
tems of buildings, in force in the country in which installation is
carried out are not complied with.
If the instructions for installation and maintenance contained in
this manual are not followed.
If unsuitable and/or uncertified materials are used for installation.
If incorrect operations are carried out that reduce the level of pro-
tection against water jets or change the protection against elec-
tric shocks by direct or indirect contact, or generate conditions
of abnormal insulation, current dispersion or overheating.
If any components or parts of the appliance are altered in rela-
tion to the original state when supplied, releasing the Manu-
facturer from any liability.
If the appliance is repaired by unauthorised personnel or if spare
parts are used other than the original ones supplied by Jacuzzi
Europe S.p.A.
7