Jacobsen LF 550 Скачать руководство пользователя страница 43

Страница: 43 / 50

ENGINE

4241262-Rev B

3-11

Figure 3-17

NOTE

Plug hoses after disconnecting to prevent loss of
hydraulic oil.

10. Disconnect upper hydraulic hose (8) from

radiator/hydraulic oil cooler.

11. Remove screws (9).

Figure 3-18

12. Disconnect lower hydraulic hose (10) from bottom of

radiator/hydraulic oil cooler.

13. Remove screws (11).

Figure 3-19

14. Remove four radiator/hydraulic cooler mounting

bracket nuts (12).

15. Carefully remove radiator/hydraulic cooler from

mount.

NOTE

Dispose of fluids properly at approved local recycling
centers. If recycling facilities are not available, contact
your local environmental department for correct disposal
procedure of fluids.

Installation

With lower radiator hose removed from radiator, flush
inside of radiator with fresh water.

Install radiator/hydraulic oil cooler by reversing order
of removal.

Fill radiator with clean water and ethylene glycol
based antifreeze mixed for coldest ambient
temperature.

Install radiator cap and start engine following
instructions in “Safety and Operation Manual.”

CAUTION

When engine reaches normal operating temperature,
check and fill coolant overflow reservoir to hot full
level.

TN3603

TN3604

Allow the engine coolant to completely cool
before removing the radiator cap. Hot coolant
sprayed from the cap can cause serious personal
injury.

TN3606

Содержание LF 550



















































Результаты поиска

Содержание LF 550

Отзывы:

Похожие инструкции для LF 550

Бренды по названию

Популярные бренды

Jacobsen LF 550, Техническое руководство по ремонту

Результаты поиска

Содержание LF 550

Отзывы:

Похожие инструкции для LF 550

Бренды по названию

Популярные бренды