Jacobsen LF 550 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 50

Jacobsen LF 550 Скачать руководство пользователя страница 5

4241262-Rev B

5

Litho In U.S.A. 10-2012

Foreword

General

This manual provides detailed information and
procedures to safely repair and maintain the following:

Jacobsen LF 550™ and LF 570™ lightweight fairway
mowers and associated accessory attachments

This manual is intended to introduce and guide the user
through the latest factory-approved troubleshooting and
repair techniques and practices.

Before you attempt to troubleshoot or make repairs, you
must be familiar with the operation of this machine. Refer
to the operator’s manual and parts manual for specific
information on these topics.

THE INFORMATION CONTAINED IN THIS MANUAL IS
BASED ON MACHINES MANUFACTURED UP TO THE
TIME OF PUBLICATION. JACOBSEN RESERVES THE
RIGHT TO CHANGE ANY OF THIS INFORMATION
WITHOUT NOTICE.

California
Proposition 65 Warning

!

WARNING

Trademark Acknowledgement

Jacobsen acknowledges the following trademarks for
company names or products mentioned within this
publication:

Lubriplate

®

is a trademark of Fiske Brothers Refining Co.

Loctite

®

and Permatex

®

are trademarks of Henkel

Corporation.

Certain vehicle components contain or emit
chemicals known to the State of California to
cause cancer and birth defects or other
reproductive harm.

«
...
3
4
5
6
7
...
»

Содержание LF 550



















































Отзывы:

Нет отзывов