manualshive.com logo in svg

Jacobsen LF 550, Техническое руководство по ремонту, Страница: 47 / 50

Поделиться
Скачать
Jacobsen LF 550 Скачать руководство пользователя страница 47

ENGINE

4241262-Rev B

3-15

3

Engine

Removal and Installation

See Figures 3-28 through 3-36.

NOTE

Naturally aspirated engine shown; turbocharged engine 
is similar.

1.

Park the mower safely. (See “Park Mower Safely” on 
page 1-6.)

2.

Allow engine to cool completely.

3.

Disconnect battery negative (–) cable at battery.

4.

Drain engine oil.

5.

Remove engine oil cooler (turbo models only). (See 
“Engine Oil Cooler (Turbocharger Engine Only)” on 
page 3-12.)

6.

Remove radiator/hydraulic cooler. (See 
“Radiator/Hydraulic Oil Cooler” on page 3-10.)

7.

Remove drive shaft. (See “Drive Shaft” on 
page 5-60.)

8.

Remove muffler and exhaust assembly. (See 
“Muffler and Exhaust Assembly” on page 3-8.)

Figure 3-28

9.

Turn fuel outlet shutoff valve (1) clockwise to close 
valve.

Figure 3-29

10. Loosen hose clamp (2) and disconnect hose (3) from 

fuel pump (4).

Figure 3-30

11. Remove throttle cable hold-down bolt (7).

12. Remove nut (5) from throttle cable wire stop (6).

NOTE

Label all wires before disconnecting to ensure correct 
installation.

13. Disconnect wire connector (8).

TN3612

1

2

TN3613

3

4

5

TN3614

8

6

7

Содержание LF 550



















































Отзывы:

Нет отзывов