manualshive.com logo in svg

Jacobsen LF 550, Техническое руководство по ремонту, Страница: 39 / 50

Поделиться
Скачать
Jacobsen LF 550 Скачать руководство пользователя страница 39

ENGINE

4241262-Rev B

3-7

3

Installation Notes

• Install fan belt by reversing order of removal.

• Adjust belt tension by loosening alternator mounting 

screws (1 and 3) and pulling alternator (2) against 
belt (4) until proper tension is achieved.

• Measure belt tension at midpoint between pulleys. 

Adjust alternator belt to 0.25–0.313 in. (6 to 8 mm) 
deflection with a tension of 20 lb (89 N).

• See engine manufacturer’s manual for further 

information.

Air Cleaner Assembly

Removal and Installation

See Figures 3-8 through 3-10.

!

CAUTION

NOTES

• Air filter on this engine is a dry type; never apply oil to 

this air filter.

• Naturally aspirated engine shown; turbocharged 

engine is similar.

1.

Park the mower safely. (See “Park Mower Safely” on 
page 1-6.)

2.

Raise the hood.

Figure 3-8

NOTE

Note orientation of air inlet (3) before removing air filter 
dust cap (1) to ensure correct installation.

3.

Release retaining clips (2) and remove air filter dust 
cap (1). 

4.

Using damp, lint-free cloths, thoroughly clean inside 
of dust cap.

Figure 3-9

5.

Pull air filter element (4) from filter housing (5). Using 
damp, lint-free cloths, clean inside of filter housing.

6.

Inspect air intake hoses (6 and 7) for wear or 
damage, and replace as necessary.

• Do not open the air cleaner assembly for 

inspection and cleaning until the air filter 
restriction gauge indicates an air filter 
restriction. Removing the air filter increases 
the possibility of dust, dirt, and contaminants 
entering the engine.

• Do not remove the air filter with the engine 

running.

1

TN3593

2

3

TN3594

4

5

7

6

Содержание LF 550



















































Отзывы:

Нет отзывов