Jacobsen HR-9016T 70541 Скачать руководство пользователя страница 46

Страница: 46 / 52

3-14

4263110-Rev B

ENGINE

Figure 3-21

Loosen hose clamp (5) and disconnect hose (4).

Remove three screws (3).

10. Remove thermostat housing (8), gasket (7), and

bypass-type thermostat (6).

CAUTION

Installation Notes

• Install thermostat by reversing the order of removal.

• Clean the gasket surface prior to installation.

• Use a new gasket during installation.

• Fill the radiator with clean water and ethylene glycol

based antifreeze mixed for the coldest ambient
temperature.

Throttle Lever

Removal and Installation

See Figures 3-22 and 3-23.

Park the mower safely. (See “Park Mower Safely” on
page 1-6.)

Remove heat shield. (See “Heat Shield” on
page 9-12.)

Disconnect battery negative (–) cables from
batteries.

Figure 3-22

NOTE

Label all wires before disconnecting to ensure correct
installation.

Disconnect wire connector (1).

Do not operate engine without a thermostat
installed. Engine damage will result from
overheating.

TN4163

TN4249

Содержание HR-9016T 70541





















































Результаты поиска

Содержание HR-9016T 70541

Отзывы:

Похожие инструкции для HR-9016T 70541

Бренды по названию

Популярные бренды

Jacobsen HR-9016T 70541, Техническое руководство по ремонту

Результаты поиска

Содержание HR-9016T 70541

Отзывы:

Похожие инструкции для HR-9016T 70541

Бренды по названию

Популярные бренды