Jacobsen Greens King 500A 63281 Скачать руководство пользователя страница 28

Страница: 28 / 60

8 MAINTENANCE

8.3

ENGINE OIL ______________________________________________________________

Check the engine oil at the start of each day, before
starting the engine. If the oil level is low, remove oil filler
cap, and add oil as required.

Perform initial oil change after the first 20 hours of
operation. Change oil every 100 hours thereafter.

See the engine manufacturer’s Owners’s Manual for
detailed service information.

After adding or changing oil, start and run engine at idle
with all drives disengaged for 30 seconds. Shut engine
off. Wait 30 seconds and check oil level. Add oil to bring
up to FULL mark on dipstick.

Use only SAE 10W30 engine oils with API classification
SG.SF/CC.CD.

Figure 8A

8.4

FUEL ____________________________________________________________________

Handle fuel with care - it is highly flammable.

Use an

approved container, the spout must fit inside the fuel filler
neck. Avoid using cans and funnels to transfer fuel.

• Store fuel according to local, state, or federal

ordinances, and recommendations from your fuel
supplier.

• Never overfill or allow the tank to become empty.

• Use clean, fresh, regular grade, unleaded gasoline

minimum 86 Octane. Refer to the engine’s operator
manual for fuel recommendations when using blended
fuel.

• See engine manual before using oxygenated (blended)

fuel.

• Do not fill above the fuel filler neck.

Upper Oil Level

Oil Filler Cap

WARNING

Never remove the fuel cap from the fuel tank, or add
fuel, when the engine is running or while the engine is
hot.

Do not smoke when handling fuel. Never fill or drain
the fuel tank indoors.

Do not spill fuel and clean spilled fuel immediately.

Never handle or store fuel containers near an open
flame or any device that may create sparks and ignite
the fuel or fuel vapors.

Be sure to reinstall and tighten fuel cap securely.

Содержание Greens King 500A 63281





























































Результаты поиска

Содержание Greens King 500A 63281

Отзывы:

Похожие инструкции для Greens King 500A 63281

Бренды по названию

Популярные бренды

Jacobsen Greens King 500A 63281, Техническое руководство

Результаты поиска

Содержание Greens King 500A 63281

Отзывы:

Похожие инструкции для Greens King 500A 63281

Бренды по названию

Популярные бренды