Jacobsen Greens King 500A 63281 Скачать руководство пользователя страница 23

Страница: 23 / 60

ADJUSTMENTS 7

7.3

BEDKNIFE ADJUSTER _____________________________________________________

Adjuster

(A)

is used to increase or decrease the

spring load on the bedknife. Adjuster

(B)

is used to

move the bedknife to the reel or away from the reel.

Once the spring is totally collapsed as a result of
many adjustments, the bedknife cannot be moved.
Back-off adjuster

(A)

before adjusting

(B)

For most applications, compress the spring to 1 in.
(25 mm).

Figure 7B

7.4

BEDKNIFE _______________________________________________________________

Read Section 7.2 before making the adjustment.

Start adjustment at the leading edge of the reel,
followed by the trailing end.

The leading end of the

reel blade is the end that passes over the bedknife
first during normal rotation.

Figure 7C

Turn adjuster

(B)

clockwise to bring the bedknife

closer to the reel or counterclockwise to back the
bedknife away from the reel.

Slide a feeler gauge or shim stock 0.001 - 0.003

in., (0.025 - 0.075 mm) between the reel blade
and the bedknife. Do not turn the reel.

Adjust the trailing end of the reel in the same

manner, then recheck the adjustment at the
leading end.

When the reel and bedknife are properly

adjusted, the reel will spin freely, and will cut a
piece of newspaper along the full length of the
reel when the paper is held at 90° to the
bedknife.

7.5

BRAKE __________________________________________________________________

A properly adjusted brake requires 10 lb. pull at top of
brake lever to engage and must have 1.50 in. (38 mm)
center to center when released.

Minor adjustments are made at the handle. Loosen
nut

(H)

, turn nut

(J)

to adjust the brake cable, then

tighten nut

(H)

If adjustments cannot be made at the handle,
remove the transport wheel, and make the
adjustment at the brake band.

Loosen screw

(K)

and pull cable to obtain desired

brake tension. Tighten screw

(K)

. Readjust

(H)

and

(J)

Figure 7D

CAUTION

To prevent personal injury and damage to the cutting
edges, handle the reel with extreme care.

Rotation

Leading Edge

Brake Band

1.50 in.

(38 mm)

Содержание Greens King 500A 63281





























































Результаты поиска

Содержание Greens King 500A 63281

Отзывы:

Похожие инструкции для Greens King 500A 63281

Бренды по названию

Популярные бренды

Jacobsen Greens King 500A 63281, Техническое руководство

Результаты поиска

Содержание Greens King 500A 63281

Отзывы:

Похожие инструкции для Greens King 500A 63281

Бренды по названию

Популярные бренды