Jacobsen Greens King 500A 63281 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 60

background image

INITIAL INSPECTION 4

13

4

INITIAL INSPECTION

4.1 GENERAL ________________________________________________________________

The set-up and testing of the unit should always be
performed by a trained technician, familiar with the
operation of the equipment.

Read each instruction completely and make sure you
understand it before proceeding with the assembly. Stay
alert for potential hazards and obey all safety
precautions.

The RIGHT, LEFT, FRONT, and REAR of the machine
are referenced from the operator’s position, facing
forward.

Accessories not included with this product must be
ordered separately. See instructions provided with
accessory for installation and parts.

This machine is shipped assembled. After unpacking,
perform the initial inspection, operating checks, and test
the Operator Presence Control (OPC).

4.2

INITIAL INSPECTION _______________________________________________________

1.

Perform a visual inspection of the entire unit, look for
signs of wear, loose hardware, and components that
may have been damaged during transport.

2.

Inspect paint and decals for damage or scratches.
Decals provide important operating and safety
information. Replace all missing or hard to read
decals.

3.

Check that the engine oil level is at the full level
mark with the engine cold.

4.

Visually check for fuel or oil leaks.

5.

Inspect lube points for proper lubrication.

CAUTION

Do not attempt to operate the machine unless you are
familiar with this type of equipment and know how to
operate all controls correctly.

!

CAUTION

The initial inspection should be performed only when the engine is off and all fluids are cold. Disengage all drives,
engage parking brake, stop engine and disconnect spark plug wire.

!

NOTICE

Mower is shipped without oil in the engine. To prevent
permanent damage, oil must be added before starting
engine. See Section 8.3 for oil specifications

«
...
11
12
13
14
15
...
»

Содержание Greens King 500A 63281





























































Отзывы:

Нет отзывов

Похожие инструкции для Greens King 500A 63281

Бренд: Kärcher Страницы: 12

Бренд: SANLI Страницы: 16

Бренд: Redexim Страницы: 12

ZTR 5000 Series

Бренд: Dixon Страницы: 70

CYCLONE MJ31-200

Бренд: Major Страницы: 88

Бренд: Gardena Страницы: 18

Бренд: Ryobi Страницы: 36

Бренд: Ferris Страницы: 60

215012, 215014, R215012, N2151

Бренд: Snapper Страницы: 52

Бренд: Yard-Man Страницы: 12

Бренд: Jacobsen Страницы: 76

Бренд: Poulan Pro Страницы: 48

Бренд: Royal Страницы: 52

Бренд: Cub Cadet Страницы: 76

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды