background image

27

07610-004-33-05-B

TROUBLESHOOTING

COMMON PROBLEMS

PROBLEM

POSSIBLE CAUSE

REMEDY

Dishmachine will not fill 

after the door is closed. 

Power “ON” light is 

illuminated.

1. Faulty rinse solenoid valve.

2. Faulty door switch.

1. Repair or replace valve as required.

2. Verify the wiring of the switch; if correct, replace switch.

Dishmachine will not fill 

after the door is closed.  

Power “ON” light is 

NOT illuminated.

1. Service breaker tripped.

2. Machine not connected to 

power source.

3. Faulty power source.

1. Reset; if the breaker trips again, contact an electrician to 

verify the amp draw of the machine.

2. Verify that the machine has been properly connected to 

the power source.

3. Verify working power source.

Dishmachine will not 
run after the door is 

closed. Power “ON” 

light is illuminated and 

the unit is filling.

1. Wash motor faulty/damaged.

2. Wash motor contactor faulty.

1. Verify that the wash motor is getting power; if so, replace 

the motor.

2. Check for continuity; if contacts are open, replace the 

contactor.

Dishmachine runs 
continuously in the wash 
cycle. 

1. Machine is in Delime mode. 

1. Select an automatic cycle by choosing I, II, or III on the 

controller display.

Wash heater does not 
work.

1. Faulty heater element.

2. Faulty heater contactor.

1. Check element for continuity; if open, replace the heater.

2. Replace the contactor.

Dishmachine fills slowly 

and/or the rinse is 
weak.

1. Clogged or obstructed rinse 

arms.

2. Low incoming water pressure.

3. Y-strainer is clogged

1. Remove and clean the rinse arms.

2. Adjust the water pressure regulator to ensure that there 

is 10 PSI flow.

3. Clean out the Y-strainer.

WARNING:

 Inspection, testing, and repair of electrical equipment should only be performed by a 

qualified service technician. Many of the tests require that the unit have power to it and live electrical 

components be exposed. 

USE EXTREME CAUTION WHEN TESTING THE MACHINE.

!

WARNING

Содержание RackStar 44

















































































Отзывы: