Jackson RackStar 44 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 80

background image

22

07610-004-33-05-B

The first rack of ware that is placed in the unit will typically reduce the temperature of
the wash tank, and the first rack might need to run through the unit again. This process

might be necessary any time the unit has not been operated for an extended period of

time, although this is dependent on the type of ware being used, its temperature, and the

ambient temperature of the kitchen area. To ensure proper operation, always observe the

temperatures of the wash and rinse when first starting the unit.

Proper preparation of ware is essential for the smooth, efficient operation of this

dishmachine.

Any ware placed in the unit should have all solid food waste and scraps removed. Ware

should also be sprayed-down before entering the dishmachine.

Place cups and glasses upside-down in racks so they do not hold water during the cycle.
Presoak flatware in warm water to assist in removing food. Load plates and saucers in the

same direction, with the food surface facing the unload end of the machine.

This dishmachine is designed to wash ware that is placed in a rack. Materials should not

be placed in the unit unless they are properly secured in a dish rack.

To start the cycle, gently push the rack into the unit on the load end. Once the wash

actuator has moved sufficiently, the unit will automatically begin to convey the dish rack

through the unit. The entire cycle is automatic.

Operators should periodically review the following items while the

machine is operating. These items are important for operating the machine in an

efficient manner.

•

Review wash and rinse temperatures and compare to the minimums on the data plate.

•

Verify the pan strainers are not becoming clogged. Keeping these free of soil and
debris allows for much better flow of water through the machine and prevents any sort

of redeposit issues.

•

Water pressure: The dishmachine is designed to run at a minimum of 15 PSI; if it is

any lower there will not be enough rinse water to properly remove detergent from the

ware.

•

Wash and rinse arm nozzles should be free of debris. Open nozzles are essential to

the operation of the dishmachine.

OPERATING INSTRUCTIONS

OPERATION

FIRST RACK

WARE

PREPARATION

WASHING A

RACK OF WARE

OPERATIONAL

INSPECTION

i

«
...
27
28
29
30
31
...
»

Содержание RackStar 44

















































































Отзывы:

Нет отзывов

Похожие инструкции для RackStar 44

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 52

Бренд: Samsung Страницы: 19

Бренд: Hoover Страницы: 144

Бренд: Gaggenau Страницы: 52

Бренд: Eurotech Страницы: 36

Бренд: Hoover Страницы: 37

Бренд: minibaby Страницы: 9

ConturaMonoPLUS

Бренд: jobst Страницы: 12

Бренд: Sammic Страницы: 16

Бренд: iLive Страницы: 53

Бренд: Amana Страницы: 16

Бренд: Hobart Страницы: 18

Бренд: Indesit Страницы: 72

Бренд: BALAY Страницы: 56

Бренд: GE Страницы: 16

Бренд: GE Страницы: 28

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды