manualshive.com logo in svg

Jackson ECOLAB ES-2000, Руководство по установке и эксплуатации

Поделиться
Скачать
Jackson ECOLAB ES-2000 Скачать руководство пользователя страница 8

ES-2000 & ES-4000 Series Installation/Operation Manual 7610-011-35-10 

Issued: 10-29-2007  Revised: N/A

SECTION 1: SPECIFICATION INFORMATION

ES-2000 SERIES SPECIFICATIONS

2

PERFORMANCE/CAPABILITIES

OPERATING CAPACITY (ES-2000’s) 

(RACKS/HOUR)

RACKS PER HOUR

40

RACKS PER HOUR (OPTION)

48

DISHES PER HOUR

1000

GLASSES PER HOUR

1000

OPERATING CAPACITY (ES-2000HH) 

(RACKS/HOUR)

RACKS PER HOUR

40

DISHES PER HOUR

1000

GLASSES PER HOUR

1000

OPERATING CAPACITY (ES-2000HHV) 

(RACKS/HOUR)

RACK PER HOUR

30

DISHES PER HOUR

750

GLASSES PER HOUR

750

OPERATING CAPACITY (ES-2000-V) 

(RACKS/HOUR)

RACK PER HOUR

30

DISHES PER HOUR

750

GLASSES PER HOUR

750

OPERATING CYCLE (ES-2000’s) 

(SECONDS)

WASH TIME

40

RINSE TIME 

15

TOTAL CYCLE TIME 

90

TOTAL CYCLE TIME (OPTION)

72

OPERATING CYCLE (ES-2000HH) 

(SECONDS)

WASH TIME

44

RINSE TIME 

25

TOTAL CYCLE TIME 

90

OPERATING CYCLE (ES-2000HHV) 

(SECONDS)

WASH TIME

44

RINSE TIME 

25

TOTAL CYCLE TIME 

120

* Total time extended by 30 seconds.

OPERATING CYCLE (ES-2000-V)

(SECONDS)

WASH TIME

40

RINSE TIME

15

TOTAL CYCLE TIME

120

*Total time extended by 30 seconds.

TUB CAPACITY

(GALLONS)

WASH TUB (MINIMUM) (ES-2000’s)

1.7

WASH TUB (MINIMUM) (ES-2000-CS)

1.2 

WASH PUMP CAPACITY

GALLONS PER MINUTE

61

TEMPERATURES 

WASH---°F (MINIMUM)

120

WASH---°F (MINIMUM) (ES-2000HH/HHV ONLY)

130

WASH---°F (RECOMMENDED)

140

RINSE---°F (MINIMUM)

120

RINSE---°F (MINIMUM) (ES-2000HH/HHV ONLY)

130

RINSE---°F (RECOMMENDED)

140

ELECTRICAL REQUIREMENTS

WASH PUMP MOTOR HORSEPOWER

3/4

NOTE: Typical Electrical Circuit is based upon (1) 125% of
the full amperage load of the machine and (2) typical
fixed-trip circuit breaker sizes as listed in the NEC 2002
Edition. Local codes may require more stringent protec-
tion than what is displayed here. Always verify with your
electrical service contractor that your circuit protection is
adequate and meets all applicable national and local
codes. These numbers are provided in this manual sim-
ply for reference and may change without notice at any
given time.

TYPICAL

TOTAL

ELECTRICAL

VOLTS

HERTZ

PHASE AMPS

CIRCUIT

ES-2000’s       115          60             1         12.0

15 AMP

WATER REQUIREMENTS

INLET TEMPERATURE (MINIMUM)

120°F

INLET TEMPERATURE (RECOMMENDED)

140°F

INLET TEMPERATURE                   
ES-2000HH MODELS (RECOMMENDED)

130°F

GALLONS PER HOUR 

68

WATER LINE SIZE NPT (MINIMUM)

3/4”

DRAIN LINE SIZE NPT (MINIMUM)

2”

FLOW PRESSURE P.S.I. 

20 ±5

MINIMUM CHLORINE REQUIRED (PPM)

50

NOTE: Always refer to the machine data plate for specific
electrical and water requirements. The material provided
on this page is for reference only and may be subject to
change without notice.

Содержание ECOLAB ES-2000




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды