Jackson ECOLAB ES-2000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 91

background image

ELECTRICAL POWER CONNECTION:

Electrical and grounding connections must comply with the applicable portions of the

National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes.

Disconnect electrical power supply and place a tag at the disconnect switch to indi-
cate that you are working on the circuit.

The dishmachine data plate is located on the right side and to the front of the
machine. Refer to the data plate for machine operating requirements, machine volt-
age, total amperage load and serial number.

To install the incoming power lines, unlock the control box. Install 3/4” conduit into
the pre-punched holes in the back of the control box. Route power wires and con-
nect to power block and grounding lug. Install the service wires (L1 & L2) to the
appropriate terminals as they are marked on the terminal block. Install the ground-
ing wire into the lug provided.

It is recommended that “DE-OX” or another similar anti-oxidation agent be used on
all power connections.

VOLTAGE CHECK:

Ensure that the power switch is in the OFF position and apply power to the dishmachine. Check the incom-

ing power at the terminal block and ensure it corresponds to the voltage listed on the data plate. If not, contact a qualified ser-
vice agency to examine the problem. Do not run the dishmachine if the voltage is too high or too low. Shut off the service break-
er and mark it as being for the dishmachine. Advise all proper personnel of any problems and of the location of the service
breaker. Replace the control box cover and tighten down the screws.

ES-2000 & ES-4000 Series Installation/Operation Manual 7610-011-35-10

Issued: 10-29-2007 Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

ELECTRICAL INSTALLATION INSTRUCTIONS

13

Ground Lug

Power Block

«
...
17
18
19
20
21
...
»

Содержание ECOLAB ES-2000




























































































Отзывы:

Нет отзывов

Похожие инструкции для ECOLAB ES-2000

Бренд: GE Страницы: 2

Бренд: Alliance Laundry Systems Страницы: 32

Бренд: Alliance Laundry Systems Страницы: 38

Бренд: Philco Страницы: 128

Бренд: Unimac Страницы: 4

3VK730XC - annexe 1

Бренд: BALAY Страницы: 24

Бренд: Silverline Страницы: 88

FLOORWASH 1000 Battery

Бренд: NAMCO Страницы: 24

Бренд: Smeg Страницы: 29

Бренд: OZTI Страницы: 24

Бренд: Miele professional Страницы: 56

Бренд: Indesit Страницы: 72

Бренд: Eswood Страницы: 13

Бренд: Baumatic Страницы: 44

Бренд: Cotech Страницы: 28

WA16CG6745 Series

Бренд: Samsung Страницы: 48

WA14N6780C Series

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды