manualshive.com logo in svg

Jackson ECOLAB ES-2000, Руководство по установке и эксплуатации

Поделиться
Скачать
Jackson ECOLAB ES-2000 Скачать руководство пользователя страница 26

1. Set rinse aid feed time to four seconds for the ES-2000XSP(PH) or six seconds for the ES-4000XSP. If the account has very
hot water temperature (160

°

F or greater), use one or two seconds as a starting point instead of the normal four to six seconds.

Adjust the rinse aid cam timer so that the rinse aid spray begins immediately after the machine finishes filling with water.

2. Perform a sheeting test. Run a load with a set of glassware and a set of flatware.

NOTE:  A new rinse aid capsule needs to be “wetted” before running a sheeting test. To wet the solid rinse aid,
run four or five cycles on the dishmachine. If the dishware does not sheet, try the following things in the order
given below:

a) Adjust the rinse aid feed time.

b) Adjust the feed water pressure.

NOTE: If the pressure is changed, the detergent titration will need to be rechecked.

c) Examine the rinse aid spray pattern. If necessary, clean and/or replace the spray nozzle.

3. Periodically, the consumption rate of the rinse aid product needs to be checked. After a minimum of two weeks, calculate the
number of racks washed per rinse aid capsule used. Do this by recording the count and taking inventory at each service call.
If the rinse aid usage is high (racks per capsule are low) and the dishware results are good (no spots), decrease the rinse aid
feed time. refer to the rinse aid consumption table below:

RINSE CONSUMPTION GUIDELINES

WATER HARDNESS

Food Soil        Soft       

Medium      

Hard   

Very Hard

(0 - 4 gpg)    (4 - 8 gpg)          (8 - 12 gpg) 

(12 - 16 gpg)

Light              1400

1000                    800

700

Medium          1200

900                     600

500

Heavy            1000

600                     400

300

(Racks per Capsule)

ES-2000 & ES-4000 Series Installation/Operation Manual 7610-011-35-10 

Issued: 10-29-2007  Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

RINSE AID FEED SET-UP

20

Содержание ECOLAB ES-2000




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды