manualshive.com logo in svg

Jackson ECOLAB ES-2000, Руководство по установке и эксплуатации

Поделиться
Скачать
Jackson ECOLAB ES-2000 Скачать руководство пользователя страница 25

1. Set the detergent feed time to four seconds for ES-2000XSP(PH), or six seconds for the ES-4000XSP. Adjust the detergent
cam timer so that the four or six second detergent spray begins immediately after the wash cycle starts.

2. Set the flush time (Detergent Flush cam) to 10 seconds. The flush must begin after the detergent feed spray and must end
at least five seconds before the machine drain opens.

3. Titrate wash water at the end of the wash cycle.

NOTE: Titration is a must. DO NOT neglect this step!

TITRATION PROCEDURES

1. Fill the titration vial to the 5 ml mark with wash solution.

2. Add 5 drops of Indicator P.

3. Titrate dropwise with Titrate 1 until the pink solution turns clear.

4. Add additional 1 or 2 drops of Indicator P to make sure of the endpoint (Chlorine sanitizer can bleach out the Indicator P and
cause premature endpoint). Continue titrating with Titrate 1 until the pink color is gone.

ES-2000 & ES-4000 Series Installation/Operation Manual 7610-011-35-10 

Issued: 10-29-2007  Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

DETERGENT SET-UP

19

Содержание ECOLAB ES-2000




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды