background image

rotate it to lock the door.
2. The door can be locked outside
without the key. First press the lock
button on the inner side of the doors
to the fixed position, then pull the
outside door handle outwards and
close the door at the same time.
3. Pull out the inside door handle to
open the door.
4. Press the lock button to lock the
door after closing it.

Cab seat

Cab seat can be classified as driver
seat, assistant driver seat and rear
row seat. Driver back seat adopts
upright seat. The angle of backrest
and the fore-and-aft position of seat
can be adjusted. The maximum
adjustable angle of the backrest is

56

.The maximum adjustable dist-

ance of the seat is 160mm.

When vehicle is in the progress of
maintenance, please clean the track
assembly of the driver seat, recoat
the lithium base grease, and tighten
all of the joint nuts again. If finding
the sliding track shaking or blocking,
it should be repaired or be replaced
with components.

Cab tilt lock mechanism

cab tilt locking device

12

1. chuck rod

2. overturn rod

3. safe locking
hook

OWNER

S MANUAL for

HFC1061,HFC1063,HFC1083

series trucks

Brief introduction of the structure:

The cab has turnover functions with
turnover

and

lockup

system.

Turnover system is composed of
torsion bar, supporting -axle, cab's
rear bracket and so on. The cab to
turnover is used by torsion power.
Lockup system is composed of right/
left lock unit, turnover lock unit, short
pull rod, long pull rod, rear bracket
of cab and so on .All of these are to
lock the cab too tightly and to make
sure the vehicle turnover automati -
cally when driving in any situation.
Please read the tilting notes on the
left door of the cab and on the upper

flange of the wheel seriously before
tilting the cab. The notes are shown
in the figure above.

Use and maintenance

In order to tilt the cab and run the
vehicle safely, please pay attention
to the following contents.

Cab tilting method and relative
notices

.

1. When stopping the vehicle on the
horizontal road, you should make
sure that there is enough space
around the cab before tilting. Or else,
the cab may be damaged while
tilting.
2. Pull up the parking brake, push
the shifting rod into the neutral
position to avoid the self -sliding of
the vehicle.

3. The cab door must be fastened
up. You should take away all the
goods on the instrument panel

seat

and floor to avoid the damage of the
door and the front windshield.
4. Disengaged the locking function of
the cab locking mechanism at first
when tilting the cab.
5. After the locking function diseng-
aged, hold the tilting rod with hand
and pull up the safety lock hook at
the same time to avoid the sudden
uplift of the cab.
6. Raise the cab slowly until it tilts to
the highest position, then lock it
carefully with lock arm on the rear
bracket.
7. When lowering the cab down, first,
hold the tilting rod and disengage

13

Notice

Содержание HFC1061

























































Отзывы: