JAC HFC1061, Руководство пользователя

Страница: 39 / 56

Notice during breaking -in
period
To improve vehicle's reliability and
economical efficiency and also to
use it longer, follow these during
breaking -in period which is speci
鄄
fied as 2000-2500km.
Before breaking-in
1. Clean vehicle with water, and
check all bolts and nuts for tighten.
2. Check the radiator for enough wa
鄄
ter, and check engine, transmission,
rear axle, and steering gear box for e
鄄
nough lubrication, also check battery
and reservoir for liquid level. Check
all tube conjunction for leakage.
3. Check brake system, driving sys
鄄
tem and steering system for correct
operation.
4. Check electrical equipment and
light instrument for correct operation,
and check brake system for normal
air pressure.
5. Check the shift gears for right, the
control parts for normality, transmis
鄄
sion for shifting smoothly, and the in 鄄
dicator should work well.
6. Check tires for proper air pres
鄄
sure..
7. Check if tools and accessories are
taken.
During breaking-in
1. Run new vehicle on flat road and
limit weight of load to 50% and 75%
of rated value separately
Not only will over loading reduce ser
鄄
vice life of vehicle, but also it will en 鄄
danger running .
2. Speed limit
gear
玉 7km/h
gear 域 14km/h
gear 芋 26km/h
gear 郁 40km/h
gear 吁 56km/h
3. Check temperature of rear axle,
transmission, steering shaft and
braking drum during initial stage.
Check whether there is abnormal
sound of chassis. Stop running if
finding those problems and rerun af
鄄
ter clearing of fault.
4. Both the cooling temperature and
oil pressure should be noticed very
well. Don't drive in high speed and
limit the temperature to 80
益 -90 益 .
5. Check cylinder head of engine,
72
OWNER 爷 S MANUAL for
HFC1061,HFC1063,HFC1083
series trucks
wheel nut, box and steel plate spring
for tighten.. Check steering brake
and clutch for normal operation.
Check steering wheel for free play
and operating stroke.
6. Oil should be replaced after
2500km running ( do it when engine
is hot), then it will be replaced again
in second- class maintenance.
After breaking -in period
1. Replace engine oil and oil filter
core. Replace oil in transmission
case and rear axle, and replace lu
鄄
brication in steering fear, also hub
bearing grease.
2. Check all external bolts and nuts
with specified torque.
3. Apply lubrication on all points
where should be lubricated.
Daily maintenance
Shoot trouble immediately if it is
found.
Doing periodic service is necessary.
Vehicle's
maintenance intervals
should be different due to different
condition of different region. Adjust
service intervals properly referring to
local condition based on relate for
鄄
mulation. Notes for maintenance of
chassis are as follows ( seasonal
maintenance is not included).
Daily maintenance
To ensure vehicle a good running
condition, do necessary check after
driving.
1. Check and fill engine with cooling
water and antirusting &antifreezing
compound. Drain off cooling water in
winter. If using antifreeze, drain off it
according to the temperature.
2. Check engine for volume of lubri
鄄
cator.
3. Check fan belt for tightening and
damage.
4. Check braking system for operat
鄄
ing and check air pressure (or hy 鄄
draulic pressure ) for sealing
5. Check steering system for operat
鄄
ing. Check bolt and nut for loosen 鄄
ing. Check cotter pin for locking up.
6. Check steel plate spring for dam
鄄
age.
7. Check tire for air pressure. Check
tire for damage and nut for tighten
鄄
ing.
8. Drain off water reservoir daily.
73