background image

- 2 -

Safety instructions

 

Pay attention to the magnet field

The magnet drive pump has a pair of strong magnets. The strong magnet 
field could adversely affect the persons who are assisted by electronic 
devices such as the pacemaker.

 

Power OFF

 Be sure to turn off the power before starting a maintenance/repair work. 
Make sure no one turns on the power while working on the pump, other-
wise it may result in a serious accident. If your work field is noisy or dark, 
let other people know about the situation by displaying a notice such as 
"POWER OFF (Maintenance)" near the power switch.

 

Wear protective clothing

Always wear protective clothing such as eye protection and protective 
gloves during pipework or dismantlement of the pump.

 

When lifting the pump

Chain the pump via eye bolts to lift it up.

 

Do not remodel the pump

Do not remodel the pump. We are not responsible for a personal injury or 
pump damage due to any modification.

 

When handling dangerous liquid

For the transfer of the harmful liquid as mentioned below, be sure to con-
duct daily inspection and maintenance for the prevention of liquid/gas leak-
age or other failure.
1. Explosive or flammable liquid
2. Corrosive or stimulus toxic liquid
3. Health hazardous liquid

 Ventilation

 Poisoning may result when handling a toxic or odorous liquid. Keep good 
ventilation in your operating site.

WARNING

Turning off power

Prohibited

Wear protective 

gear

No Remodeling

Содержание AMP 40


































Отзывы: