background image

- 10 -

1. Before installation

Example of recommended piping

 Discharge pipe
 Discharge valve
 Check valve
 Pressure gauge
 Motor
 Pump
 Flexible joint
 Vacuum gauge
 Suction pipe
 Suction valve
 Gate valve
 Air vent piping
 Pipe support

1

2

3

11

10

13

10

12

11

6

5

9

7

4

8

7

12

Within
1m

Concrete foundation

Foundation bolt

Baseplate

Liner

Liner

Installation

1. Installation location

•  The pump should be installed on a flat foundation where is free from vibration or torsional force.
•  Spacing for the motor removal (for back pull out) and maintenance (assembly and dismantlement) are 

needed.

•  Installation surface should be larger than the pump base.

2. Positioning

•  Install the pump as close to the suction tank in flooded suction system.
•  If the flooded suction system can not be realized, install the auxiliary piping for priming and a foot valve at 

the suction pipe end.

3. Pump mounting

•  See the diagram below for mounting the pump in the foundation.
•  For the pump without the base plate, note that the pump can not be dismantled with the foot supports of 

the cover and bracket fixed in the foundation.

Содержание AMP 40


































Отзывы: