manualshive.com logo in svg

Ivoclar Vivadent 747827AA, Руководство по эксплуатации

Поделиться
Скачать
Ivoclar Vivadent 747827AA Скачать руководство пользователя страница 49

49

2. Conduct a software update 

If the USB stick with the software file is already connected, the 
 furnace automatically searches for a valid software file. If the USB 
stick has not yet been connected with the furnace, do so now.
Press the 

[Execute]

 button. 

3. The status bar shows the progress of the update.   

4. Complete the software update 

The following messages are displayed:

Software update successful

Software update failed

   The furnace has to be switched off and on again by means of the mains switch at the rear of the furnace to 

complete the software update.

  Important information

 

 Please note that modified Ivoclar Vivadent programs may be overwritten during a software update. Individual 
programs are not affected and will not be overwritten.

5.4.5  Software Update

Software updates can be easily installed on the furnace by means of a USB stick. A USB memory stick, which contains a 
current software file (e.g. P510:V1.10.iv) is required. The software version on the USB memory stick must be higher than 
the one installed on the furnace (see Selection – Information)

The free software updates for Programat furnaces are available from 

www.ivoclarvivadent.com/downloadcenter

. 

  Back-up your data before performing a software update.

A software update requires only few steps:

1. Open software update

Scroll to page 2 in the home screen and press the  

[Software update]

 button.

5. Operation and Configuration

Содержание 747827AA

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды