manualshive.com logo in svg

IVEK DIGISPENSE 3020, Руководство пользователя

Поделиться
Скачать
IVEK DIGISPENSE 3020 Скачать руководство пользователя страница 108

DIGISPENSE 3020 CONTROLLER MODULE

Page 3-108

7 April, 2011

IVEK Corp.

P03L011B

3.3.14  Operating The System

There are several different modes of operation providing the Controller Module with its vast functional flexibility. On
initial power-up, these modes must each be sequenced in the proper order to assure proper operation.

3.3.14.1Setup (Figure 3.6)

The following steps will guide you through a basic setup for turning your system on for the first time:

1.  On the rear of the Controller Module

a.  Make sure the 1/0 (On/Off) (1a) switch is set to 0 (Off).
b.  Connect the power cord to the Controller Module (1b) and the power source.
c.  Connect the Actuator Cable; the larger connector connects to the Controller Module (1c).

2.  On the Actuator Module

a.  Connect the other end of the Actuator Cable (2a).
b.  Make sure the Actuator is secure.

3.  Set the inlet and outlet port configuration. Refer to section 3.1.6.

4.  On the Pump Module

NOTE

Make sure the inlet tubing is larger than, or the same size as, the outlet tubing. Start with the reservoir even
with or slightly higher than the Pump Module and the Pump Module even with or slightly higher than the
dispense tip. Adjust as necessary to fit your application.

a.  Connect the inlet fitting and tubing (3a)
b.  Connect the gland inlet fitting and tubing (3b) (

*

optional)

c.  Connect the outlet fitting and tubing (3c)
d.  Connect the gland outlet fitting and tubing (3d) (

*

optional)

3.3.14.2 Start-up

a.  Switch the 1/0 power switch to the "1" position.

b.  The display will illuminate and show the following

information. The status will change from Initializing
to Idle and the information for

your

 system will be

displayed including the current recipe and pump
size and there may have additional push-button
selections depending on your system settings.

 

Refer to Section 3.2.4 in your manual for field
descriptions.

REFERENCE REQUIRED may be flashing
indicating the system needs to be referenced or
SETUP C may be flashing indicating no pump is selected.

c.  Press the Reference push-button to reference the system and the Actuator Module will reference.

  0

DIGISPENSE

3020

IDLE

  2
  3

4

IVEK CORPORATION

  5

http://www.ivek.com

  6
    7

RECIP  =  ##

      8

PUMP  =  ##

  9
   10

 11

12

Press function button below to proceed

 13
 14

XXXXXXX  XXXXXXX REFERENCE XXXXXXX

 15  XXXXXXX

XXXXXXX REQUIRED XXXXXXX

Содержание DIGISPENSE 3020






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды