background image

LOVESHAW 

an 

ITW

 Company 

Little David® 

Warranty

 

For: 

 All Standard Little David® Semi-Automatic Case Sealers. 

         All Standard LD-16 Series Fully Automatic Case Sealers. 

                  All Special Application Case Sealers (Fully & Semi-Automatic).

 

 

2 YEAR WARRANTY ON DRIVE MOTOR 
2 YEAR WARRANTY ON GEAR MOTOR 

 

2 YEAR WARRANTY ON GEAR REDUCER 
3 YEAR WARRANTY ON TAPE CARTRIDGE 

(EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL WEAR, 
TEAR AND REPLACEMENT, WHICH ARE WARRANTED ONLY TO BE FREE 
FROM DEFECTS IN MATERIAL AND WORKMANSHIP.)

 

1 YEAR ON PLC 
1 YEAR ON SERVO DRIVE 
1 YEAR ALL OTHER PARTS 

 

 

(EXCEPT FOR WEAR AND MOVING PARTS.) 

 

*LIMITED WARRANTY – 

LOVESHAW, 

AN 

ITW 

COMPANY (HEREIN AFTER “

LOVESHAW

”) WARRANTS ONLY THAT THE GOODS SOLD 

BY IT SHALL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP, UNDER PROPER AND NORMAL USE AND 
MAINTENANCE, AS FOLLOWS: 
 
 DRIVE 

MOTOR -    

2 YEARS 

 GEAR 

REDUCER -   

2 YEARS 

 GEAR 

MOTOR -    

2 YEARS   

(THIS APPLIES TO SIDE BELTS ONLY) 

 TAPE 

CARTRIDGE -  

3 YEARS                 (EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL  

WEAR, TEAR AND REPLACEMENT, WHICH ARE WARRANTED ONLY TO BE 
FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP.) 

 PLC -  

 

 

1 YEAR 

 SERVO 

DRIVE -    

1 YEAR 

 

ALL OTHER PARTS -  

1 YEAR   

(EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL   
WEAR, TEAR AND REPLACEMENT, WHICH ARE WARRANTED ONLY    
TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP.) 
 

THE WARRANTY PERIOD SHALL COMMENCE AS OF THE DATE OF DELIVERY TO THE PURCHASER.  THE OBLIGATION OF 
LOVESHAW UNDER THIS WARRANTY IS STRICTLY LIMITED TO THE COST OF REPAIRING OR REPLACING, AS LOVESHAW MAY 
ELECT, ANY PART OR PARTS THAT PROVE IN LOVESHAW’S JUDGMENT TO HAVE BEEN DEFECTIVE IN MATERIAL OR 
WORKMANSHIP AT THE TIME THE GOODS WERE SHIPPED FROM LOVESHAW’S PLANT.  ANY WARRANTY CLAIM NOT MADE IN 
WRITING TO LOVESHAW AT ITS HOME OFFICE WITHIN THE APPLICABLE WARRANTY PERIOD AND WITHIN 10 DAYS OF FAILURE 
WILL NOT BE VALID.  THIS IS THE SOLE AND EXCLUSIVE REMEDY AVAILABLE UNDER THIS WARRANTY.  UNDER NO 
CIRCUMSTANCES WILL LOVESHAW BE LIABLE FOR INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES. 
 
IF REQUESTED BY LOVESHAW, PURCHASER SHALL RETURN ANY DEFECTIVE PART OR PARTS TO LOVESHAW’S PLANT, 
FREIGHT PREPAID.  ALL WARRANTY PART REPLACEMENTS AND REPAIRS MUST BE MADE BY LOVESHAW OR A LOVESHAW 
AUTHORIZED TO HANDLE THE GOODS COVERED BY THIS WARRANTY.  ANY OUTSIDE WORK OR ALTERATIONS DONE WITHOUT 
LOVESHAW’S PRIOR WRITTEN APPROVAL WILL RENDER THIS WARRANTY VOID.  

LOVESHAW, 

AN 

ITW 

COMPANY WILL NOT 

ASSUME ANY EXPENSE OR LIABILITY FOR ANY REPAIRS MADE TO ITS GOODS OUTSIDE ITS WORKS WITHOUT ITS PRIOR 
WRITTEN CONSENT.  THIS WARRANTY SHALL NOT APPLY TO ANY ITEM THAT HAS NOT BEEN USED, OPERATED, AND 
MAINTAINED IN ACCORDANCE WITH LOVESHAW’S RECOMMENDED PROCEDURES LOVESHAW SHALL HAVE NO LIABILITY 
WHATSOEVER WHERE THE GOODS HAVE BEEN ALTERED, MISUSED, ABUSED OR INVOLVED IN AN ACCIDENT.  
 
NO PERSON IS AUTHORIZED TO MAKE ANY WARRANTY OR TO CREATE ANY LIABILITY BINDING UPON LOVESHAW.  WHICH IS 
NOT STATED IN THIS WARRANTY.  THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, 
EXPRESSED OR IMPLIED, WHICH ARE HEREBY EXCLUDED.  IN PARTICULAR, THE IMPLIED WARRANTY OF MERCHANTABILITY, 
AS WELL AS THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED. 
 
 

LOVESHAW 

AN

 ITW 

COMPANY

 

2206 EASTON TURNPIKE,  BOX 83 SOUTH CANAAN, PA  18459 
TEL:  570.937.4921  -  800.572.3434  -  FAX:  570.937.3229 

 

 

 

 

 
 
 
 

Содержание LOVESHAW LITTLE DAVID LD7D/M


























































Отзывы: