ITW LOVESHAW LITTLE DAVID LD7D/M Скачать руководство пользователя | Manualshive

Страница: 9 / 57

background image

LOVESHAW

an

ITW

Company

MAIN FRAME

STARTER SWITCH:

THE STARTER SWITCH

IS MOUNTED ON THE OPERATOR SIDE OF THE MACHINE. IT INCORPORATES A

CIRCUIT BREAKER THAT IS SET TO TRIP AT THE PROPER RATING OF THE MOTOR. TO REPLACE THIS
SWITCH, FIRST DISCONNECT THE MACHINE FROM THE ELECTRICAL SUPPLY. REMOVE THE SWITCH
BY LOOSENING THE TWO FASTENING SCREWS AND PULL THE SWITCH FROM THE ELECTRICAL BOX.
REMOVE THE WIRES AFTER FIRST NOTING THEIR CONNECTIONS TO THE SWITCH.

TO REPLACE THE STARTER SWITCH, REVERSE THE ABOVE PROCEDURE.

SIDE RAILS:

THE SIDE RAILS CENTER AND ALIGN THE BOX AS IT IS BEING PROCESSED. THEY ARE SET MANUALLY
BY LOOSENING THE SIDE RAIL LOCK HAND WHEEL COUNTERCLOCKWISE. MOVE THE SIDE RAILS IN
UNTIL BOTH SIDE RAILS COME IN CONTACT WITH THE BOX. RELOCK THE SIDE RAILS BY TURNING
THE SIDE RAIL LOCK HAND WHEEL CLOCKWISE.

IF A SIDE RAIL NEEDS REPLACING, REMOVE THE TWO SCREWS ON THE TOP OF THE SIDE RAIL AND
REPLACE WITH NEW ONE. SECURELY TIGHTEN SCREWS WHEN REPLACING A SIDE RAIL.

BELTS:

TWO BELTS LOCATED ON THE BED OF THE MACHINE DRIVE THE BOX THROUGH THE MACHINE.
THE BELTS RUN OVER A DRIVE ROLLER LOCATED AT THE EXIT END OF THE MACHINE, AND THEN
ARE THREADED OVER THE INFEED ROLLERS LOCATED AT THE INFEED END.

TO REPLACE A BELT, BRING THE BELT LACING PIN TO THE TOP OF THE MACHINE. PUSH THE BELT
TENSIONING BRACKET TOWARD THE EXIT END OF THE MACHINE AND PULL THE BELT LACING PIN.
REMOVE THE OLD BELT AND REPLACE WITH THE NEW ONE. FOLLOW THE BELT THREADING
DIAGRAM. MAKE SURE THE SPRINGS ON THE BELT TENSIONING ROLLER BRACKET ARE IN PLACE.

EACH BELT IS REPLACED SEPARATELY, HOWEVER, IT IS RECOMMENDED THAT BOTH BELTS BE
REPLACED AT THE SAME TIME. IT IS IMPORTANT THAT FACTORY SUPPLIED BELTS BE USED SINCE
THEY ARE OF SPECIAL CONSTRUCTION.

BELT THREADING DIAGRAM

KEY

PART

NUMBER

DESCRIPTION

1 PSC301244-4

BELT

2 PSC301217-4

DRIVE

ROLLER

3 PSC301232

BELT

TENSIONING

SPRING

4 K286D

GUIDE

ROLLER

5 PSC301208-5

INFEED

ROLLER

BRACKET

6 PSC301211-4

INFEED

ROLLER

«
...
7
8
9
10
11
...
»

Содержание LOVESHAW LITTLE DAVID LD7D/M


























































Отзывы:

Нет отзывов

Похожие инструкции для LOVESHAW LITTLE DAVID LD7D/M

Бренд: Omcan Страницы: 12

Бренд: HOFFEN Страницы: 34

Бренд: Jata Страницы: 20

Бренд: Concept2 Страницы: 128

Бренд: Anvil Страницы: 8

Бренд: HEALLUX Страницы: 21

Бренд: Oceanic Страницы: 217

Бренд: Eagle Страницы: 28

Deluxe Digital Table Warmer

Бренд: Earthlite Страницы: 4

Бренд: Kasanova Страницы: 2

Бренд: Cadco Страницы: 2

Бренд: Vesta Precision Страницы: 23

Бренд: Thermopatch Страницы: 22

Бренд: Thermopatch Страницы: 23

Бренд: True Страницы: 2

Seal Fresh RHVS1CAN

Бренд: Russell Hobbs Страницы: 2

Бренд: Russell Hobbs Страницы: 20

Бренд: Imetec Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды