ITW LOVESHAW LITTLE DAVID LD7D/M Скачать руководство пользователя страница 4

Страница: 4 / 57

LOVESHAW

ITW

Company

BELT LAGGING INSTALLATION

IF THE BELT MOVES TO THE LEFT OR RIGHT AT THE EXIT END OF THE MACHINE,

THEN THE BELT LAGGING (FRICTION) MATERIAL ON THE DRIVE ROLLER MUST BE

CUT ON THE SAME SIDE THAT THE BELT IS MOVING TOWARDS. TO ACCOMPLISH

THIS, FIRST REMOVE THE BELT THAT IS MOVING OUT OF LINE AS DESCRIBED

ABOVE, SO THAT THE EXIT ROLLER CAN TURN FREELY, AFTER THE MACHINE

IS TURNED ON.

TURN ON MACHINE AND WITH A UTILITY KNIFE, CUT ABOUT 1/8” OFF THE BELT

LAGGING MATERIAL BY PLACING THE POINT OF THE KNIFE ON THE LAGGING
MATERIAL WHILE THE DRIVE ROLLER IS TURNING. BE SURE TO PLACE THE
KNIFE ON THE ROLLER SO THAT THE ROLLER IS MOVING AWAY FROM THE POINT
OF THE KNIFE.

AFTER A COMPLETE CUT IS MADE, TURN MACHINE OFF AND WITH THE POINT OF

THE KNIFE, LIFT UP A SECTION OF THE CUT LAGGING AND PULL OFF UNTIL IT IS

REMOVED FROM THE DRIVE ROLLER COMPLETELY. (THIS CAN BE DONE BY

JOGGING THE MACHINE ON/OFF WHILE PULLING THE CUT STRIP OF LAGGING).

REPLACE BELT AND CHECK ALIGNMENT. BELT WILL HAVE MOVED TO THE

OPPOSITE SIDE THAT WAS CUT. THIS PROCEDURE MAY HAVE TO BE REPEATED

UNTIL THE BELTS ARE CENTERED.

Содержание LOVESHAW LITTLE DAVID LD7D/M


























































Результаты поиска

Содержание LOVESHAW LITTLE DAVID LD7D/M

Отзывы:

Похожие инструкции для LOVESHAW LITTLE DAVID LD7D/M

Бренды по названию

Популярные бренды

ITW LOVESHAW LITTLE DAVID LD7D/M, Руководство пользователя

Результаты поиска

Содержание LOVESHAW LITTLE DAVID LD7D/M

Отзывы:

Похожие инструкции для LOVESHAW LITTLE DAVID LD7D/M

Бренды по названию

Популярные бренды