background image

Section 14

Warranty

Innovative Technical Solutions Inc. warrants that the ACCUTEK III is free
from defects in workmanship or material. This warranty is valid for a period
of one year from the date of purchase and is given only to the original pur-
chaser of the ACCUTEK III. Except where required by applicable legisla-
tion, this warranty is not transferrable. This warranty is void if the
ACCUTEK III is used for anything other than its intended purposes or if any
modifications or alterations are made to the ACCUTEK III. Innovative
Technical Solutions Inc.’s liability under this agreement shall be limited to
repair and/or replacement of the ACCUTEK III.

INNOVATIVE TECHNICAL SOLUTIONS INC. SHALL IN

NO EVENT BE LIABLE FOR LOSS OF PROFITS OR

SPECIAL OR INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING FROM THE BREACH OF EXPRESS

OR IMPLIED WARRANTIES OR NEGLIGENCE.

To exercise this warranty, the purchaser, at its sole cost and expense, shall
return the ACCUTEK III to Innovative Technical Solutions Inc. together
with the following:

1.

Copy of sales receipt

2.

Date of failure

3.

Type of failure

4.

Test being performed at time of failure

5.

Name, address and phone number of contact person.

All warranty claims must be received by Innovative Technical Solutions Inc.
within 90 days of the unit failure. Upon receipt of the defective ACCUTEK
III
, Innovative Technical Solutions Inc. will repair or replace and return the
product without charge within a reasonable period of time. Upon return, the
ACCUTEK III shall have a warranty on the same terms and conditions as
stated above for a period of 90 days or the balance of the original warranty,
whichever period is greater. This agreement constitutes the entire agreement
between the parties and supersedes any previous agreement, understanding
or order between the parties. Should the terms and conditions of any pur-
chase order issued in connection with the agreement conflict with the terms
contained herein, the terms of this agreement shall prevail. No modifications
or waiver of the terms of this agreement shall be binding unless made in
writing and signed by both parties.

www.

.com

[email protected]

1.800.561.8187

Содержание Accutek III































Отзывы: