background image

9

6 pole DIN socket 

Manual controls

8 pole DIN socket 

Table column 2

8 pole DIN socket 

Table column 2

8 pole DIN socket 

Table column 1

8 pole DIN socket 

Table column 1

6 pole DIN socket 

Manual controls

Table E: ST2

8 pole DIN socket 

Table column 4

8 pole DIN socket 

Table column 3

Table 4 E: ST4

Control units

The synchronous control systems are used to control height-adjustable table 

systems for 2 or 4 table columns
2 table columns  EU; 230 VAC  

 

USA/CDN; 120-277 VAC

4 table columns  EU; 230 VAC  

 

USA/CDN; 120-277 VAC

 

ƒ

The on-time is 10%, which means that the table columns can 

be run for 2 minutes in continuous operation and will then 

switch off for 18 minutes.

 

ƒ

Check the seating of all plug connections.

 

ƒ

Use a power cord to connect to the mains.

 

ƒ

The control system and manual controls must be positioned and secured as 

appropriate to local conditions. If necessary, alter their position.

 

ƒ

The installation site should be dry, free of dust and away from direct sunlight.

 

ƒ

The environmental temperature for operating the control system must not fall 

below 5 °C or above 35 °C.

 

ƒ

Consequently, you should not install the control system:

  - above or in front of heat sources (e.g. radiators), 

  - in locations that are exposed to direct sunlight, 

  - in small, unventilated, damp rooms, 

  - on or near highly flammable materials or 

  - near high-frequency devices  

  (e.g. transmitters, radiation-emitting devices or similar equipment).

 

ƒ

Ensure that connecting cables and electrical lines are not bent, pulled or 

subjected to mechanical loads. In particular, cables must not be clamped in 

the foot area of the table columns (safety area of approx. 10 mm around the 

table column feet).

 

ƒ

It is advisable to install surge protection to protect against the types of 

electrical surges that can occur during thunderstorms. Consult an electrical 

engineer.

 

ƒ

Never open the control system’s housing or the power pack! Unauthorised 

opening of the housing and inappropriate repairs can cause hazards for us-

ers and shall invalidate the warranty. Only the manufacturer’s personnel are 

authorised to open or repair the electrical systems.

 

ƒ

Do not allow any liquids to penetrate inside the control system or the power 

pack as this could result in an electric shock or short circuit.

 

ƒ

Use only a dry or slightly damp cloth to clean the control system and the 

manual controls.

 

ƒ

Stop using the device immediately if it begins to emit smoke or odour, makes 

unusual noises or shows visible signs of damage. Disconnect the system 

from the mains by removing the plug.

 

ƒ

The control system may only be used with item table columns.

5. Electrical connections for height-adjustable tables

Observe the following points when installing and operating the control system:

Содержание Work bench 4 E FIFO

















Отзывы: