iSystem iC5000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 69

background image



iSYSTEM, October 2016

9/69

Licenses

iC5000 introduces a new licensing model. As with all iSYSTEM tools, winIDEA license is required. Valid
winIDEA license also includes iSYSTEM technical support service, and can be requested either by phone or by
e-mail

[email protected]

.

Besides  winIDEA  license,  at  least  one  CPU  architecture  license  is  required  in  order  to  connect  to  the  target
microcontroller via debug interface. Advanced functionalities such as trace, profiling and code coverage become
available via trace license. Make sure that the target debug connector to which ic5000 system connects, exposes
microcontroller trace port (ETM, Nexus …) when trace functionality is required.

iSYSTEM development tools feature a hardware based license scheme, which saves costs comparing to per-seat
based  licenses.  All  licenses  are  kept  in  the  iC5000  development  system,  which  conveniently  allows  moving
iC5000 unit from one development seat to another.

When new iC5000 system is shipped from iSYSTEM, CPU architecture and trace licenses are preprogrammed
by the iSYSTEM test department. With such  a new system, only winIDEA license needs to be requested from
iSYSTEM  after  receiving  the  iC5000  system.  Additional  CPU  architecture  license,  which  are  purchased  later,
must be programmed by the user.

Below  picture  shows  the  sticker,  which  can  be  found  on  iC5000  system,  identifying  which  CPU  architecture
licenses  were preprogrammed by  the iSYSTEM test department. Below  picture  shows preprogrammed  Cortex-
M3 and MPC56xx licenses.

«
...
7
8
9
10
11
...
»

Содержание iC5000






































































Отзывы:

Нет отзывов

Похожие инструкции для iC5000

Growing Together

Бренд: Stokke Страницы: 13

Бренд: Elnec Страницы: 2

HALOHOME HWAD1BLE40AWH

Бренд: Eaton Страницы: 3

Бренд: StarTech.com Страницы: 2

Бренд: Hama Страницы: 4

PCI to USB Host Adapter 60800

Бренд: LSI Страницы: 10

Бренд: Omegon Страницы: 2

Бренд: U.S. Converters Страницы: 8

Бренд: Zero One Страницы: 10

Бренд: Acard Страницы: 26

Бренд: Poly Страницы: 6

Бренд: Digitus Страницы: 4

Бренд: Clarity Страницы: 8

Бренд: Choetech Страницы: 38

Бренд: Vetus Страницы: 2

Бренд: Natec Страницы: 12

Бренд: Canyon Страницы: 65

Бренд: Dynex Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды