iSystem iC5000 Скачать руководство пользователя страница 19

Страница: 19 / 69



iSYSTEM, October 2016

19/69

Debug Cable Adapters

Various cable adapters are available depending on the specific target architecture and the target debug connector.
They are used to connect iC5000 development system to the target.

Ordering code

Adapter

IC50111-1

20-pin 2.54mm ARM Cable Adapter

IC50112

14-pin 2.54mm ARM Cable Adapter

IC50113-AMP

20-pin 1.27mm AMP Cortex Debug Cable Adapter

IC50114

Mictor 38-pin ARM ETM 8-bit Cable Adapter

IC50115

Mictor 38-pin ARM ETM 16-bit Cable Adapter

IC50116

10-pin 1.27mm Cortex Debug Cable Adapter

IC50118

20-pin 1.27mm Cortex Debug Cable Adapter

IC50119

20-pin 1.27 x 2.54mm Compact TI-20 Cable Adapter

IC50130

26-pin 2.54 mm ColdFire Cable Adapter

IC50140

6-pin 2.54mm BDM Cable Adapter

IC50141

6-pin 2.54mm S12Z Cable Adapter

IC50150

14-pin 2.54mm MPC5xxx Cable Adapter

IC50152
IC50152-12

Mictor 38-pin MPC5xxx Nexus 16-bit Cable Adapter

IC50153

16-pin 2.54mm Freescale COP Cable Adapter

IC50154

51-pin GLENAIR Cable Adapter

IC50155

Mictor 38-pin PPC4xx RISCTrace Cable Adapter

IC50156

50-pin Samtec MPC5xxx Nexus 16-bit Cable Adapter

IC50158

Mictor 38-pin MPC5xx Nexus 8-bit Cable Adapter

IC50160

16-pin 2.54mm Infineon JTAG Cable Adapter

IC50160-ECU14

10-pin 1.27mm Tricore ECU14 Cable Adapter

IC50160-MEDC17

10-pin 1.27mm Tricore MEDC17 Cable Adapter

IC50162

6-pin 2.54mm Infineon I2C Cable Adapter

IC50163

10-pin 1.27mm Infineon DAP2 Wide Cable Adapter

IC50164

22-pin Samtec ERF8 DAP2 Cable Adapter

IC50170

16-pin 2.54mm Renesas 78K0R Serial Cable Adapter

IC50171

20-pin 2.54mm Renesas V850/RH850 Cable Adapter

IC50172

26-pin KEL Renesas V850 Cable Adapter

IC50173

14-pin 2.54mm Renesas SuperH Cable Adapter

IC50174

10-pin 2.54mm Renesas 78K0 Serial Cable Adapter

IC50175

14-pin 2.54mm Renesas RL78 Serial Cable Adapter

IC50176

14-pin 2.54mm Renesas RH850 Cable Adapter

IC50176-EPS

10-pin 1.27mm Renesas RH850 Cable Adapter

IC50177

Mictor 38-pin Renesas RH850 Nexus 16-bit Cable Adapter

IC50190

4-pin ERNI ST STM8 Cable Adapter

Signal direction definition used throughout this document:

- output from the debugger to the target microcontroller

- input to the debugger from the target microcontroller

Содержание iC5000






































































Результаты поиска

Содержание iC5000

Отзывы:

Похожие инструкции для iC5000

Бренды по названию

Популярные бренды

iSystem iC5000, Справочник по аппаратуре

Результаты поиска

Содержание iC5000

Отзывы:

Похожие инструкции для iC5000

Бренды по названию

Популярные бренды