iSystem iC5000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 69

background image



iSYSTEM, October 2016

22/69

Texas Instruments Microcontrollers

Note  that  targets  based  on  Texas  Instruments  (TI)  ARM  microcontroller  may  feature  Texas  Instruments  ARM
14-pin target debug connector with TI proprietary pinout.

A dedicated adapter is available for Texas Instruments ARM 14-pin pinout and can be ordered separately under
IAPIN20ARM14TI ordering code.  Make sure you don’t mix up Texas Instruments pinout with standard 14-pin
2.54mm ARM pinout (cable adapter IC50112).
Double check the pinout of the target debugs connector with the debug cable adapter pinout before connecting it
to the target for the first time.

Ordering code

IAPIN20ARM14TI

With this adapter, the following pinout is valid on the target side:

Signal

direction

Signal description

Signal

Pin Pin Signal Signal description

Signal

direction

Output

Standard JTAG

TMS

1

2 nTRST

Standard JTAG

Output

Output

Standard JTAG

TDI

3

4

GND

Ground

Input

Reference voltage

VTref

5

6

NC

Not connected

Input

Standard JTAG

TDO

7

8

GND

Ground

Input

Return TCK

RTCK

9

10

GND

Ground

Output

Standard JTAG

TCK

11 12

GND

Ground

Input

Debug Acknowledge

BERR

13 14 nSRST

System Reset

In/Out

ARM7 14-pin TI target connector

A jumper is present on the adapter. If this jumper is set, the SYSTEM RESET line is connected to pin 14 on the
target side. If SYSTEM RESET is not needed, then this jumper should be removed.

Note: this adapter can only be used with 20-pin 2.54mm ARM Cable Adapter

The adapter connects to the target via a 14-pin 2.54 mm connector (for example Yamaichi: FAS-1401-2101-2-
0BF). A target should feature a matching part (for example WÜRTH ELEKTRONIK: 612 014 216 21).

«
...
20
21
22
23
24
...
»

Содержание iC5000






































































Отзывы:

Нет отзывов

Похожие инструкции для iC5000

Бренд: Linksys Страницы: 2

Бренд: F-One Страницы: 2

Бренд: Aretas Страницы: 4

Бренд: Daikin Страницы: 8

Бренд: Linksys Страницы: 68

Бренд: Fujitsu Страницы: 97

PRIMEQUEST 2000 Series

Бренд: Fujitsu Страницы: 188

PRIMEQUEST 2000 Series

Бренд: Fujitsu Страницы: 734

Бренд: Westermo Страницы: 28

Бренд: OBDLink Страницы: 12

Бренд: Allen-Bradley Страницы: 12

Бренд: ECKELMANN Страницы: 12

Бренд: Abocom Страницы: 1

Бренд: Linksys Страницы: 2

Бренд: Linksys Страницы: 31

USB100TX - EtherFast 10/100 USB Network Adapter

Бренд: Linksys Страницы: 28

Бренд: Linksys Страницы: 64

Бренд: AmbiCom Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды