iSystem iC5000 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 69

background image



iSYSTEM, October 2016

54/69



10-pin 1.27mm Infineon DAP Cable Adapter

Ordering code

IC50161

Note: This product is obsolete and is fully replaced with IC50163

This adapter is used to connect the iC5000 development system to Infineon XC166, XC2000 or TriCore based
target. It connects to Debug/Trace module on one side and to the target debug connector on the other side. It can
be used for targets featuring 10-pin 1.27mm pitch target debug connector with Infineon DAP pinout.

From Rev. E1 on, Infineon 3-pin DAP debug interface (Wide Mode) is supported (labeled “Infineon DAP2”).
Older revisions support 2-pin DAP (one clock line + one bidirectional data line) interface only (labeled “Infineon
DAP”).

From Rev. D1 on, Hot Attach operation without connecting/disconnecting the adapter from the target is
supported. Rev. D1 newly introduces jumper J1.

With jumper J1 in position 1-2 (default), normal debug operation is configured. The debugger drives MCU reset
line low during the initial debug connection and then takes control over the microcontroller.

With  jumper  J1  in  position  2-3,  Hot  Attach  operation  is  configured.  In  this  case,  all  debug  signals  from  the
iC5000 unit are disconnected and the target  starts running  as soon as  the power is applied to the  target. When
Hot Attach command is issued from winIDEA, the debugger connects to the MCU and control over the MCU is
taken  without  resetting  the  MCU.  Depending  on  the  target  MCU,  refer  to  the  XC166/XC2000  or  the  TriCore
technical notes document for more details on Hot Attach configuration and use.

The following pinout is valid on the target side:

Signal

direction

Signal description

Signal

Pin Pin

Signal

Signal description

Signal

direction

I

Reference voltage

Vref

1

2

DAP1

Bidirectional data

I/O

Ground

GND

3

4

DAP0

DAP clock

O

Ground

GND

5

6

USER_IO

Optional

O

Not Connected

NC

7

8

USER_IN

Optional

O

Ground

GND

9

10

RESET

System Reset

I/O

10-pin Infineon DAP pinout

Note: 10-pin 1.27mm Infineon DAP Cable Adapter features resettable fuses on pins 1, 2, 3, 4, 5, 6, 8, 9 and 10.
These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive
current fades away.

The adapter connects to the target via a 10-pin 1.27mm connector (for example SAMTEC: FFSD-05-01-N). A
target should feature a matching part (for example SAMTEC: SHF-105-01-L-D-TH).

«
...
52
53
54
55
56
...
»

Содержание iC5000






































































Отзывы:

Нет отзывов

Похожие инструкции для iC5000

Бренд: Wagan Страницы: 8

Бренд: Renesas Страницы: 18

Бренд: Asahi KASEI Страницы: 2

Бренд: Belkin Страницы: 18

Бренд: Pace Страницы: 15

Бренд: VSmart Страницы: 9

Бренд: Nektar Страницы: 2

Бренд: ACTiSYS Страницы: 8

Бренд: Keysight Technologies Страницы: 24

Бренд: Dynex Страницы: 20

DL2x170h - ProLiant - G6

Бренд: HP Страницы: 29

Бренд: SP Controls Страницы: 2

Бренд: IBM Страницы: 11

Бренд: WENKO Страницы: 4

Бренд: Tyco Electronics Страницы: 8

Бренд: Tyco Страницы: 4

Бренд: Planet Страницы: 69

Бренд: Romac Industries Inc. Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды