Isotra SCREEN HR7, screen HR8-ZIP Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 23

background image

MEASUREMENT AND ASSEMBLY MANUAL

Validity of the manual: 1. 6. 2017

16

3. GENERAL INFORMATION

3.1. CHECKING THE INSTALLATION

The installation is checked by testing its functionality. The screen is lowered and raised again. This should proceed
smoothly, and no creases should develop during lowering.

3.2. MOUNTING THE BOX

This can be done in several ways:



Secure the box by hanging it from the mounting brackets (see method 1), or



- Open the box. Remove the fabric roll from the box by tapping upwards on the fabric roll so the end pops out of the

click-in retainer. Affix the box to the mounting surface with the extra pan head screws (through the back or the top of
the box). Do this for each console and in the centre. Re-install the fabric roll and the box cover.

3.3. FINISHING

Space between screen box and wall

Apply a small amount of silicon caulk in the gap between the screen box and mounting surface in order to prevent any
potential movement.
To fill the gaps at the top and the sides (between the screen box and the mounting surface when mounting brackets
are used), you can use joint sealing strip or the special U-profile (see points G3 and G4) which is available separately..

Space between guide rails and wall

Apply a small amount of silicon caulk in the gap between the guide rails and mounting surface in order to prevent any
potential movement.

DVC/DVS

When installing DVC/DVS linked screens, it is recommended that one person be available to push each guide rail onto
the console pivot, the bottom slat into the guide rail and the zipper into the grey U-shaped part of the plastic guide
profile.

4. INSTALLATION OF CONTROLS

4.1. ELECTRICAL CONNECTIONS

Note

: The connections must be made by a qualified installer (refer to guarantee card 2.1). Electrical installation and

connection diagrams must be followed correctly. The electrical accessories employed must comply with the current
standards and/or requirements.

«
...
14
15
16
17
18
...
»

Содержание SCREEN HR7, screen HR8-ZIP
























Отзывы:

Нет отзывов

Похожие инструкции для SCREEN HR7, screen HR8-ZIP

NEW DARKENING BLIND

Бренд: Claus Страницы: 4

Бренд: weinor Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды