Isotech milliK Скачать руководство пользователя страница 91

Страница: 91 / 102

Page 91 of 102

923 milliK manual - issue: 1.10

reported value is in °C. If the specified channel does not exist, the milliK returns “channel not

found”.

Example: to measure the temperature of channel 1’s thermocouple reference junction use:

MEAS:RJC? 1

8.6.23

Command MONitor<channel#>?

Format: MONitor<channel#>?

<timeout>

Reports the next measurement (including units) made on <channel#> within the specified

<timeout>, in seconds. If a measurement is not made within the specified timeout, the milliK

reports “Timeout”. If the milliK detects that the channel is not enabled, it reports “Channel

Not Enabled”. The milliK reports the value followed by the units (separated by a comma):

Where units

= R

(for ohms)

=mV

(for milli-volts)

= K

(for Kelvin)

= C

(for °C)

= F

(for °F)

Example: if channel 2 is configured to measure temperature in °C, a typical response to

MON2? 5

would be “1.23456,C”.

8.6.24

Command CALibrate:UNLock

Format: CALibrate:UNLock

<password>

Unlocks the milliK to allow calibration adjustment. The milliK always powers up in the

locked state. Calibration can be re-locked by cycling the power to the milliK or using

CAL:LOCK

(see section 8.6.25).

Example: to unlock (enable) the calibration adjustment on a milliK with the default password

(“1234”), use:

CAL:UNL 1234

8.6.25

Command CALibrate:LOCK

Format: CALibrate:LOCK

Locks the milliK to prevent calibration adjustment.

Содержание milliK







































































































Результаты поиска

Содержание milliK

Отзывы:

Бренды по названию

Популярные бренды

Isotech milliK, Руководство по эксплуатации пользователя

Результаты поиска

Содержание milliK

Отзывы:

Бренды по названию

Популярные бренды