iSMA iSMA-B-W0202 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 41

background image

iSMA-B-W0202 User Manual

www.ismacontrolli.com

DMP263en | 1st Issue rev. 3 | 05/2022

page 32 of 41

Cooling Mode

In this mode, the output is controlled as a typical thermostat, based on the Setpoint

register and control value (input value) with differential parameter defined in the

Differential register.
The output signal works in 2 states, low and high.
If the control value is lower than or equal to the difference of the Setpoint register and

Differential register, the output is in low state.
If the control value is higher than or equal to the sum of the Setpoint register and

Differential register, the output is in high state.
Output in low state:
Control value <= Setpoint

–

Differential

Output in high state:
Control value >= Se Differential
The cooling mode algorithm is shown in chart below.

Figure 19. Cooling mode algorithm

7.5.2 Command Register (40020)

The module has a special Command register (40020). The Command register is used to

remotely execute an action (simulate light switch/PIR). The action is executed by changing

WARNING!

In the case if the temperature sensor has failed (got disconnected or shortcut), then

the heating mode does not work, and the output stays in the false state.

WARNING!

In the case if the temperature sensor has failed (got disconnected or shortcut), then

the heating mode does not work, and the output stays in the false state.

«
...
30
31
32
33
34
...
»

Содержание iSMA-B-W0202










































Отзывы:

Нет отзывов

Похожие инструкции для iSMA-B-W0202

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: EasyIO Страницы: 18

Бренд: Faulhaber Страницы: 66

Бренд: UCS Страницы: 4

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: Matelec Страницы: 16

Бренд: Technische Alternative Страницы: 68

Бренд: Paser Страницы: 2

Бренд: M-system Страницы: 7

Бренд: UMAX Technologies Страницы: 54

Бренд: AccessPRO Страницы: 2

Бренд: Transient Modules Страницы: 5

Бренд: Quicksmart Страницы: 10

Бренд: Aerotech Страницы: 112

ServeRAID M1215 SAS

Бренд: IBM Страницы: 35

Бренд: QUNDIS Страницы: 2

Бренд: Caen Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды