background image

              

• 

Plug the included AC adapter.  

(110V AC to 12V AC)

• 

Confirm that  all 4 Red LED lights in front of  this unit are double 

BLINKING

• 

Use one of your telephones and unplug the cord for L1/L2 from it and connect it
to 1/2/3 PHONE LINES jack on SX8600 (the 1

st

 jack from 12VAC), now connect

1/2/3 TELEPHONE jack on SX8600 (3

rd

 jack) to your telephone using the

provided phone cord, make sure you have dial tone on your lines 1 and 2

• 

Now unplug the cord for L3/L4 from your phone and connect it to 3/4 PHONE
LINES jack on SX8600 (the 2nd jack from 12VAC) and connect 3/4
TELEPHONE jack on SX8600 (4

th

 jack) to your telephone using the provided

phone cord, make sure you have dial tone on your lines 3 and 4

• 

Observe that as you connect the lines  the blinking lights turn OFF.

 

(on non

existing lines the lights keep blinking and that is OK)

• 

• 

• 

• 

Alternatively you may use a splitter (T adapter) at the Wall jack to connect  both
this device and a telephone (in that case the 3

rd

 and 4

th

 jacks are not connected)

• 

Set the volume to mid level.

• 

Insert the Flash card into the blue connector in the front of unit, the Green status

        LED in the back of the unit will turn ON.

 

  

                 

 

  

 
 
 

 

                   IN   IN   OUT  L3/L4    L1/L2/L3   L3/L4    L1/L2/L3 12VAC

                                               TELEPHONE     PHONE LINES    600ma 

WALL

JACK

PHONE

WALL

 JACK

PHONE

110 V

 AUDIO

TEST

             Problems 

Possible Cause /  Solution

P16

 

Innovative Telecommunication Technology LLC.

 1112 Montana Ave  Suite 250  Santa Monica, CA  90403 USA

 Toll-Free: 800-747-0708 Tel: 310-899-0078 Fax: 310-230-5346

® 

10. 

Hold Music activates in
a conference call or
when two phones pick
up at same time

• 

If for any reason the hold music is activated
inadvertently, it can always be deactivated by pressing
the FLASH button in any setting.

• 

Conference calls can be done a better way: Press
FLASH,  you will get a dial-tone now dial the phone
number of the 2

nd

 party then press FLASH to join the

two calls together.

      

L1   L2                                                     L3   L4

3/4          1/2

6. 

MOH works but audio
does not stop when call
is picked up in 1 or 3
settings.

• 

Wire distance to adapter is too long, Centralize  the
location of device to be as close as possible to all the
phones.  Try the 2 setting for maximum power.

• 

If you are re-wiring  “daisy chain” wiring works better than
” star”  or “home run” or  Independent  wiring

• 

Press FLASH button to stop the music.

7. 

Some Phones work ,
some do not

  

• 

All your phones need to be same  model for activation
in 1 or 2 settings. If you mix different phone models,
Use the 3 setting (refer to pages 3 or 4 for more
details)

8. 

Randomly  Hold music
starts to play by it self
or does not activate in
1, 2 or 3 settings

• 

The call needs to be on Hold min. 2 sec. before  you
may pick it up.

• 

When you hang up,  wait 2 seconds before selecting
the same line again.

• 

Check for extra devices sharing  that line like Message
indicator, Answering machine, Alarm system, Modem
etc. Use a “privacy module” between the line and that
extra device to keep them off the line when line is
being used by your phone.

• 

Set your Alarm system and/or your DSL line to share
FAX line.

• 

Excessive wiring- Total wire length per line must be
under 500 feet  ( Ex: if you have 9 wall jacks -no matter
spare or a phone plugged in-  each connected via a
100 foot wire to a common point then your total wire
length is 9 x 100=900 feet )

• 

Use FLASH button to deactivate music.

9. 

Audio shuts off or
flickers

  

• 

Extensive audio volume. Lower  the volume to proper
level.

  

MIC  AUDIO

A B C   1 2  3

VOLUME

STATUS  1  2

REC

BANK

SWITCH

Flash Card

Please note that just one telephone is optionally connected to this
device, other telephones remain connected to their own wall jacks.

Model # SX8600    

Rev 24E5

All-In-One Auto Att Gr
Music-On-Hold Player/Recorder/Adapter

Содержание SX8600









Отзывы: