Invacare 3G Storm Series Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 192

background image

SECTION 10—BASE FRAME

Part No. 1104849

89

3G Storm Series® Wheelchairs

2. When reinstalling the rear seat stop screw, ensure the seat support bracket is located

in-between both seat stop screws. Use Loctite 242 and tighten securely.

FIGURE 10.5

Removing/Installing Seat Stop Screws

Adjusting Weight Distribution

NOTE: For this procedure, refer to FIGURE 10.6.

NOTE: Seat mount plates and seat support brackets allow the seat frame to be repositioned along
the base frame. The range is determined by position of the seat stop screws. The front seat stop screw
is positioned at 4-inches and the rear seat stop screw is positioned at 10-inches. Both seat stop screw
positions are measured from the front of the base frame.

NOTE: The position of the seat support brackets is factory set at 7-inches, this measured from the
front of the base frame to the front of the seat support bracket. This will put about 70% of the total
weight of the chair and user over the large wheels. However, this setting may not be the most
desirable in terms of maneuverability, front rigging clearance and comfort for the user.

Adjustment Options

NOTE: This section will provide the user with some knowledge of what to expect if the following
adjustments are made.

1. Moving the seat forward.

• Advantage: This adjustment allows more clearance for front riggings and a more

stable “feel” for the user.

• Disadvantage: More weight is put on front casters and makes turning more

difficult.

NOTE: This option can also be accomplished by moving the motor backward on the suspension
arm. Refer to Repositioning the Motor on page 90.

2. Moving the seat rearward.

• Advantage: Makes turning easier and provide better traction for the large wheels.

• Disadvantage: This adjustment, however, allows less clearance for front riggings

and the user will experience more engagement of the anti-tippers.

NOTE: This option can also be accomplished by moving the motor forward on the suspension arm.
Refer to Repositioning the Motor on page 90.

Base Frame

Seat Support Bracket

Rear Seat Stop Screw

Front Seat Stop Screw

«
...
87
88
89
90
91
...
»

Содержание 3G Storm Series

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3G Storm Series

Бренд: Harmar Mobility Страницы: 34

Бренд: identités Страницы: 2

Бренд: EZee Life Страницы: 3

Бренд: Rhythm Healthcare Страницы: 2

Бренд: panthera Страницы: 2

Бренд: Timago Страницы: 6

Бренд: Harbor Freight Tools Страницы: 4

Бренд: Remedic Страницы: 2

Бренд: Freedom Innovations Страницы: 4

Бренд: Perfect Vision Страницы: 20

Бренд: Mercado Medic Страницы: 2

SAFETYSURE THE KNEE SLING

Бренд: MTS Systems Страницы: 2

872FOCPBLC00ABD187

Бренд: Focal Meditech Страницы: 13

Papillon head support

Бренд: Focal Meditech Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды