292
IO
S AVE THESE INSTRUCTIONS
(292IO) BUBBLE SPA WITH POOL ENGLISH 7.5” X 10.3” PANTONE 295U 07/15/2016
English
Page 13
OPERATION
On/Off Button:
Once the unit is plugged in, use this button to active the control unit panel
buttons. The light next to the button is green when activated. Press this button to turn off all
currently activated functions.
NOTE:
The On/Off button may appear as a black button in the center of the control panel.
Heat Button:
Use this button to turn on and off the heating system for the spa (A) side only.
The pump will heat the spa water until the water temperature reaches the set temperature, and
then the heater will go into rest while the
fi
ltration pump will continue to run for an additional 8
hours with the indicator light “A” showing green. During these 8 hours, every time the spa water
temperature drops 1-2°C (1.8-3.6°F) below the set temperature the heating system will restart.
After the additional 8 hours, the heater will rest for about 2 hours, and the
fi
ltration system
will switch to the “B” side, and
fi
lter the water for 2 hours with the indicator light “B” showing
green. After 2 hours, the
fi
ltration system will switch back to the “A” side, and run for 8 hours.
The heater will restart to compensate for any spa water temperature drop from the initial set
temperature. This cycle is repeated again until the unit is manually turned off. When the
fl
ame
icon on the display is red, the heating system is activated. When the
fl
ame icon turns green,
the water is at the set temperature. The heating system is at rest and the
fi
ltration system will
continue working nonstop.
When the indicator light “A” is illuminated, the following options are available:
• During the heating process, press the
fi
lter button for 3 seconds to switch the
fi
ltration function
to the “B” side, the heater will stop and the
fl
ame icon will turn off. The
fi
ltration will run for
2 hours; then the
fi
ltration will automatically switch back to the spa (A) side, and the heating
system resumes its operating cycle.
• Stop the
fi
ltration while the heater is at rest mode: press the
fl
ame button
fi
rst to turn off the
heater, and then the
fi
lter button.
•
Press the
fl
ame button while the heater is at rest mode will turn off the heating system only,
the
fi
ltration system will operate for two cycles or 24 hours before it turns off automatically.
When the indicator light “B” is illuminated and the heater is in standby mode (indicated
by a fl ashing green fl ame icon), the following option is available:
• Press the
fl
ame button will stop the
fi
ltration on the “B” side of the tub, and turn on the heater
and
fi
lter functions on the “A” side of the tub.
IMPORTANT:
The following conditions will lead to slow water heating.
• The ambient temperature is lower than 10ºC (50ºF).
• Outdoor wind speed is above 3.5-5.4 m/s (8-12 mph).
• The air bubble function is activated when heating the spa water.
• The spa is not properly covered with the spa cover when the water is heating.
Celsius/Fahrenheit Toggle Button:
The temperature can be displayed in either Fahrenheit
or Celsius. The system’s default is Celsius.
CAUTION:
NEVER use the spa if indicated water temperature is more than 40°C (104ºF).
1: On/Off Button
2: Heat Button
3: Celsius/Fahrenheit Toggle Button
4: Temperature Increase Button
5: Temperature Decrease Button
6: Water Filter Button
7: Bubble Button
8: LED Display
9: Filtration section indicator light ("A" side
fi
ltration;
"B"
side
fi
ltration)
B
A
7
6
5
4
3
2
8
1
9
B
A
SPA CONTROL UNIT PANEL
