Interroll ZoneControl Скачать руководство пользователя страница 49

Страница: 49 / 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

49 von 54

Decommissioning and disposal

CAUTION

Risk of injury from following incorrect procedure.

Decommissioning must only be carried out by authorised, qualified personnel.

Only decommission the ZoneControl when the system has been disconnected from the power supply.

Switch off the power to the ZoneControl and ensure that it cannot be unintentionally switched on again.

9.1

Decommissioning

Remove all cables from the ZoneControl.

Loosen the screws that have been used to attach the ZoneControl to the conveyor frame.

Remove the ZoneControl from the conveyor frame.

9.2

Disposal

The operating company is responsible for disposing of the ZoneControl according to correct procedure. In

doing so, the industry-specific and local provisions for disposing of the ZoneControl and its packaging must

be observed.

Содержание ZoneControl























































Результаты поиска

Содержание ZoneControl

Отзывы:

Похожие инструкции для ZoneControl

Бренды по названию

Популярные бренды

Interroll ZoneControl, Руководство по эксплуатации

Результаты поиска

Содержание ZoneControl

Отзывы:

Похожие инструкции для ZoneControl

Бренды по названию

Популярные бренды