Interroll ZoneControl Скачать руководство пользователя страница 26

Страница: 26 / 54

26 von 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

Assembly and installation

5.4

Electrical installation

The ZoneControl is fitted with an internal, non-replaceable fuse that serves exclusively to protect the device.

The protection of the supply cables must be guaranteed by the operator.

The ZoneControl should be fixed to the side of the conveyor on which the RollerDrive cable is located. All of the

connections should be routed to one side of the conveyor to simplify cabling.
The cabling of the PTP connection must always following the direction of the conveyor, that is to say that the PTP

downstream connection of the upstream zone must be connected to the PTP upstream connection of the downstream

zone etc. This also applies if one/several ZoneControl(s) have to be fitted on the other side of the conveyor.

1 Direction of travel

4 Power supply

2 ZoneControl

5 Peer-to-peer connection

3 RollerDrive

6 Package

Required cables:

Содержание ZoneControl























































Результаты поиска

Содержание ZoneControl

Отзывы:

Похожие инструкции для ZoneControl

Бренды по названию

Популярные бренды

Interroll ZoneControl, Руководство по эксплуатации

Результаты поиска

Содержание ZoneControl

Отзывы:

Похожие инструкции для ZoneControl

Бренды по названию

Популярные бренды