manualshive.com logo in svg

Intermec EasyLan 100, Руководство пользователя

Поделиться
Скачать
Intermec EasyLan 100 Скачать руководство пользователя страница 28

0100 Access Point User's Manual

2-6

This is for the graphics

Making a Backup Copy of the Boot Disk

Make a backup copy of your original Access Point boot disk and place the
original disk in a safe place. Run the Access Point from the backup copy.

To make a backup copy

1. Insert the Access Point boot disk in the 3.5 inch drive of your host PC. You

may have to remove it from the Access Point drive.

2. From a DOS prompt on your host PC, type

XCOPY A: A: /S

Note

: If your 3.5 inch drive is the drive B of your PC, substitute B for A in the

command line.

3. Follow the instructions on your host PC screen to copy the disk.

4. Remove the copied disk and place it in the Access Point drive. Place the

original disk in a safe place.

5. Install the faceplate covering the 3.5 inch drive on the front panel of the

Access Point.

The Access Point boot disk is copied.

Performing a Quick Installation

Caution
ETSI and FCC regulations mandate that the Access Point antenna not be
alterable. Therefore, Access Point uses a custom antenna connector. Do not
attempt to use a different antenna or you may damage the connector and the
bridge.

Conseil
La réglementation ETSI et FCC exige que l'entenne Access Point ne soit pas
modifiable. Par conséquent, l'antenne Access Point utilise un connecteur
d'antenne personnalisé. Ne tentez pas d'utiliser une antenne différente car vous
risquez d'endommager le connecteur et le pont.

CAUTION

Содержание EasyLan 100

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды