background image

15

IMPORTANT NOTE

You should have now completed installing the Intermatic 
Multipurpose Control and available accessories.  Prior 
to wiring the equipment to the control, you should 

 

read and understand Step #6, which clearly defines 
the individual circuit ratings, available mode settings 
and their relative wiring diagrams.  Below is a quick 
reference Mode Table.  This will help you to quickly 
identify each possible circuit output.  Refer to Step #6 
for a more complete definition.

MODES OF OPERATION

MODE 

SELECTION

MODE 1

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6*

MODE 7

CIRCUIT #1

AUX 1

PUMP HIGH

PUMP

PUMP HIGH

PUMP L1

AUX 1

PUMP HIGH

CIRCUIT #2

AUX 2

PUMP LOW

AUX 2

PUMP LOW

PUMP L2

AUX 2

PUMP LOW

CIRCUIT #3

AUX 3

AUX 3

CLEANER 

PUMP

AUX 3

AUX 3

COMMON

CLEANER 

PUMP

*Circuit 1 will circulate pool or spa without heating body of water.

NOTE:

 Auxiliaries can be used to control any piece of equipment.

CHOOSE MODE 1 TO CONTROL ANY THREE INDEPENDENT LOADS

CHOOSE MODE 2 TO CONTROL A TWO-SPEED PUMP AND ONE INDEPENDENT LOAD

CHOOSE MODE 3 TO CONTROL A SINGLE SPEED PUMP WITH A CLEANER PUMP   

AND ONE INDEPENDENT LOAD

CHOOSE MODE 4 TO CONTROL A TWO-SPEED PUMP WITH A CLEANER PUMP

CHOOSE MODE 5 TO CONTROL TWO INDEPENDENT DEVICES WHERE ONE DEVICE  

REQUIRES BOTH POWER LEGS TO BE DISCONNECTED

CHOOSE MODE 6 TO CONTROL THREE INDEPENDENT LOADS. FIREMAN’S SWITCH WILL 

CLOSE ONLY WHEN CIRCUIT IS MANUALLY TURNED ON.

CHOOSE MODE 7 TO CONTROL A TWO-SPEED PUMP  

WHERE BOTH POWER LEGS ARE REQUIRED TO BE DISCONNECTED

26

Setting The Mode

1.   With a small blunt instrument, press and hold the 

Mode Button

 (Approximately 5 seconds) until the 

display shows 

SET MODE

 and the 

Mode Number 

blinks

.

2.   Use the Up and Down 

arrow keys

 to cycle through 

all available modes.  Each 

circuit output will be 

defined 

as you cycle through the available modes.

3.   Once the desired mode number is displayed, press 

and release the 

ENTER key.

  This saves it to memory 

and exits the set mode programming.

Circuit outputs will 

be defined

 

Arrow Keys

SET MODE

ENTER key

Mode Button

Mode 

Number

Blinks

DISPLAY

Содержание P1353ME






















Отзывы: