Interlogix DDV1016AM Скачать руководство пользователя страница 4

Страница: 4 / 52

4 / 52

P/N 146667999-

1 (ML) • REV G • ISS 19AUG19

•

Obscuring the detector field of view with large objects,
such as furniture

Microwave hazards:

•

Mounting surface susceptible to vibrations

•

Metal surfaces reflecting microwave energy

•

Water movement through plastic pipes

•

Moving or vibrating objects like fans, heating or air-
conditioning ducts

AM hazards:

•

Moving objects less then 1 m in front of the detector

•

Small insects on the detector

•

Modern fluorescent lighting in close proximity (within
1.5 m)

WARNING!

The equipment is not earthed. Any

external circuit connected to the equipment must be
located within the same building and connected to a
protective earthing conductor.

Wire insulation of cables connected to the equipment must
conform to IEC 60332-1-2 and IEC 60332-1-3 or IEC 60332-
2-2, depending on the wire cross sectional area, or IEC TS
60695-11-21, regardless of cross sectional area. Alternatively,
such wires must comply with UL 2556 VW-1.

The detector power supply source must be power limited at
15 W.

We recommend that the detector is regularly walk tested and
checked at the control panel.

To install the detector:

1. Lift off the custom insert (see Figure 2, items 1 and 2).

2. Using a screwdriver, carefully prise open the detector (see

Figure 2, items 3 and 4).

Caution:

Do not touch the pyroelectric sensor (Figure 6).

3. Take out the cover screw (Figure 4, item 2).

4. Fix the base to the wall between 2.0 and 3.0 m (6.6 and

9.8 ft.) from the floor.

See Figure 4. In all positions use a minimum of two M4
screws from the standards DIN 7505B, DIN 96, DIN 7996,
or a screw with a head with 8 mm diameter and a flat
surface.

- For flat mounting, use screws in positions A.

- For corner mounting, use screws in position B or C.

Note:

For EN 50131 Grade 3 installations, do not use

mounting position C.

- To install the pry-off tamper ST400, use mounting
positions A. ST400 mounting position is shown as item 3
in Figure 4. Open the outlet in the back plate (Figure 5,
item 2).

5. Wire the detector (see Figures 4 and 12). Use back plate

cable inlets (Figure 5, item 1) and cable gutter (Figure 5,
item 3).

6. Select the desired jumper and DIP switch settings (see

“Setting the detector” below for more information.

7. Remove the blinders and add the stickers, if required. See

“Configuring the coverage pattern” on page 6 for more
details.

8. For ceiling-mount applications, use the SB01 swivel-mount

bracket. SB01 mounting position is shown as item 1 in
Figure 4.

9. Close the cover, insert the cover screw, and place the

custom insert.

Connections

See Figure 12.

Table 1: Detector Connections

Terminal Label

Explanation

1, 2

GND,
+12V

Power supply connection (9 to 15 V



, 12 V



nominal)

3, 4

ALARM

Alarm relay output (33

Ω). Use jumper JA to

set the onboard EOL resistor in series with the
relay. See

“Jumpers” below.

5, 6

TAMPER Tamper switch output (0

Ω). Use jumper JT to

set the onboard EOL resistor in series with the
switch. See

“Jumpers” below.

Walk test This input enables and disables the LED (walk

test On/Off). Walk test mode can only be
entered when detector is in Day mode (pin 8).
Active high or low is determined by SW1-3
(see

“SW1-3: Polarity” on page 5).

Day /
Night

This input switches the detector in day (show
memory on the LED indicator) or night mode
(activates the alarm memory and clears
previous stored alarms). Active high or low
polarity is determined by SW1-3

(see “SW1-3:

Polarity

” on page 5).

9, 10

Fault

Fault Relay output (33

Ω). Use jumper JF to

insert one of the on-board EOL resistors in
series with the relay. See

“Jumpers” below for

the correct resistor settings.

Notes

•