Interflex IF-4070 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 19

Interflex IF-4070 Скачать руководство пользователя страница 8

Page 8

Electrical Wiring

i

This chapter shows the electrical wiring for connecting slave terminals, sensors and electrical devices.

There is a danger of electric shock in case of faulty 230VAC installations.
Severe injuries, or in worst case even death, can result.



Installation of 230V systems as well as Schuko sockets may only be carried out by
electricians or other qualified persons.

NOTE

For secure, reliable operation, the following must be observed:



Our specified cable lengths. The specifications indicate the permitted cable lengths that
guarantee reliable system function.



Our specified cable type. Install only data and control cables with cable shielding, e.g.
cable type JY(ST)Y with anti-static shield.



Electrical installation standards. The terminal controller may only be operated via electrical
systems that comply with current national standards, e.g. DIN VDE 0100.



Separator in compliance with EN 600950-1. Install an easily accessible Schuko socket with
its own fuse in the vicinity of the terminal controller.



An even distribution of the slave terminals among the 3 BUS interfaces. Without changing
the default interface settings, you can connect up to six slave terminals to BUS 1, up to four
slave terminals to BUS 2 and up to six slave terminals to BUS 3. Always connect a slave
terminal with address 1 to BUS 1.

3

3

3

8x input

8x REL Out
up tu 30V 2A

2

3a

4

5

1

2

2

2

Ethernet

RS 485 BUS 3

RS 485 BUS 2

RS 485 BUS 1

6

RS 232
RS 485

1m

=RJ 45 wiring box

Figure 4: Electrical Wiring
No.

Cable Length Recommended Cable Type

1

Power cable with Schuko plug (not needed with PoE supply)

2

RJ45 patch cable, shield braiding recommended

5m

CAT 3 or higher

3

RS485 BUS data lines with up to 8 slave terminals

1200m

J-Y(ST) Y 4x 2x 0,6 mm

2

3a

RS485 branch cable from slave terminal to BUS cable

100m

J-Y(ST) Y 4x 2x 0,6 mm

2

4

Control cable

Not specified

J-Y(ST) Y 4x 2x 0,6 mm

2

5

Connection cable to floating sensors

100m

J-Y(ST) Y 4x 2x 0,6 mm

2

6

Alternative PC connections with RS232 or RS485

25 / 1,000 m

J-Y(ST) Y 4x 2x 0,6 mm

2

«
...
6
7
8
9
10
...
»

Содержание IF-4070




















Отзывы:

Нет отзывов