Interflex IF-4070 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 19

Interflex IF-4070 Скачать руководство пользователя страница 11

Page 11

Connection of BUS Data Cables with Slave Terminals

You can connect the data cable with slave terminals with RJ45 plugs (on the front panel) or with screw terminals
(internal).
The following applies for both alternatives:



Three RS485 BUS interfaces are available for connection of 16 slave terminals.



Up to 8 slave terminals can be connected to each BUS interface.



A slave terminal with hardware address 1 must always be connected to BUS 1.



The connected slave terminals must have different hardware addresses.



Without changing the default interface settings, you can connect up to six slave terminals to BUS 1, up to four
slave terminals to BUS 2 and up to six slave terminals to BUS 3. Always connect a slave terminal with address
1 to BUS 1.



When connecting a terminal with an LAP reader, software version 7.12.3 or higher must be loaded.

Connection of Bus Data Cables with RJ45 Plugs

NOTE

For trouble-free operation, the following must be observed:
The shields of the data cables are grounded via the RJ45 female connectors. Use, therefore, only
shielded cables and shielded connection components like HiRose male connectors, etc.

Figure 7: Connection of bus data cables with RJ45 plugs

Bus 1, 2, 3

1 + Tx / Rx
2 - Tx / Rx

1 + Tx/ Rx

2 - Tx/ Rx

Shield

-

Tx

/

Rx

+

Tx

/

Rx

Shield

RS 486 BUS cable, length up to 1200 m

-

Tx

/

Rx

+

Tx

/

Rx

Shield

Spur line,

cable length

up to 100m

Patch cable connection

Terminal Bus 1 or
Terminal Bus 2, or
Terminal Bus 3

up to 8 slave terminal

Spur line,

cable length

up to 100m

RJ45

wiring box

Shield

i

LED indication of data traffic



The bus LED lights up (flickers) when there is data traffic with slave terminals.



A brief lighting up indicates that the terminal controller is unable to establish a connection to the slave
terminal. Check the connection of the data cable and the slave terminals.

Connection to screw terminal strip KL.6

After opening the housing cover you can connect three RS485 BUS data cables to the screw terminal Kl.6. Use
terminal "shield" for grounding the cable shields. Secure the cable with a strain relief.

KL.6 Terminal assignment
1 Tx/Rx +

BUS 3

2 Tx/ Rx - BUS 3
3 Shield

For cable shield

4 Tx/Rx +

BUS 2

5 Tx/Rx -

BUS 2

6 Shield

For cable shield

7 Tx/ Rx +

BUS 1

8 Tx/ Rx - BUS 1

«
...
9
10
11
12
13
...
»

Содержание IF-4070




















Отзывы:

Нет отзывов