Interflex IF-4070 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 19

Interflex IF-4070 Скачать руководство пользователя страница 15

Page 15

Information on parameterization

Please keep the following in mind during parameterization:

1. Interflex calls the software for configuration and indication of device functions "OC Task", the commands

"Commands".

2. A connection to OC Task is possible:

a. via the network, via TELNET or SSH connection and the factory-set IP address (see device label) or via the

IP address 172.18.70.52, which can be set with the Restart push-button

1

.

b. via the RS232 service interface, e.g. with a PC and the communication software Hyper-Terminal. You can

find information about the connection in chapter >Connection of the Service Interface<.

3. OC-Task can be accessed after logging in with

root

and entering a password.

4. The prompt

root@

signalizes readiness to receive commands and data.

5. The following input syntax must be observed:

-  Commands are written with small letters.
-  Options are separated from the command by a blank (space bar) and a minus sign.
-  The command

-?

displays an overview of possible options.

- Press ENTER to confirm your command and optional data.

6. To save new data, you must confirm the prompt

Write to EEPROM (y/n) ?

with the

y

key.

7. Changed data become effective only after a "RESET" with the command $ oc –s.
8. TELNET and SSH connections must be properly terminated after the configuration.

Point 3: Establish a TELNET Connection

An initial TELNET connection is usually established via the factory-set IP address. You can find the address on the
housing lid. To perform the configuration, you must first log in.

Login



Access to the console and Linux commands is granted after a login with

root

and entry of the password

Haydnstr

(observe correct spelling).



The prompt

"root@"

signalizes readiness to receive commands and data.

1

See chapter: >Controller front side<

«
...
13
14
15
16
17
...
»

Содержание IF-4070




















Отзывы:

Нет отзывов