background image

21 

 

Breaking of the restraining elements during unfavorable wind; in this case, there is the 
risk for every exposed person to get hit by the structure 

Structural loss of stability, if the prescription previously indicated will not be respected 

6. CHECKS AND MAINTENANCE 

 

It is necessary to periodically check the general state of the structure, of the connections between 
the various components, of the and the PVC awnings

The PVC awning can be washed with mild soap and then rinsed with water only. After the cleaning, 
the PVC shall be well dried before fold, in order to avoid the creation of moulds.  

The  checks  and  maintenance  frequency  indicated  below  is  to  be  considered  as  the  minimum 
interval  to  grant  efficiency,  security  and  durability  of  the  product  of  the  product  in  normal  use 
situations.  

A constant supervision is recommended, in order to act promptly in case of anomalies. 

Ordinary maintenance, checks and lubrification operations must be done after the frame has been 
uninstalled. 

ATTENTION

: Every modification or manomission which has not been previously authorized by the 

constructor, will cause the dacay of every responsibility of the constructor on the product conformity.

 

The constructor suggests to constantly control the box, making the scheduled checks, and prompt 
act in case of anomalies, unusual damages or breaks. 

 

6.1. ORDINARY MAINTENANCE

 

 

CAUTION 

The  maintenance  deadlines  indicated  here  below  are  to  be  considered  indicative,  and  refers  to  normal 
usage  conditions.  The  product  conditions  can  vary  in  relation  to  the  type  of  usage,  the  usage  frequency 
and to the environmental features (presence of dust,..). In case of heavy duty conditions, the maintenance 
checks should be increased.

 

 

 CAUTION 

It is advisable to use the same kind of lubricant during all the interventions. The greasing points must be 
cleaned accurately with compressed air before the lubrification; in this way,  dust, mud and other foreign 
matters will not mix with the lubricant. 

 

Содержание KIT BOX SERRA























Отзывы: