IntelliSAW 400.00152.0001 Скачать руководство пользователя страница 13

Страница: 13 / 18

Module Integration Manual

Page 13 of 18

Interrogator RF Board (400.00152.xxxx)

PPROVED

NTENNAS

The following antennas have been approved for use with the INTERROGATOR RF BOARD:

IntelliSAW Part #

Type

Gain

IA-xx-5-y

Monopole (5 cm mast)

-1 dBi

IA-xx-9-y

Monopole (9 cm mast)

+1 dBi

IA-xx-17-y

Monopole (17 cm mast)

+3.2 dBi

IA-xx-TPD

Patch inverted F (PIFA)

+3.5 dBi

Part Number (“xx”) indicates magnetic (MM) or bolt (BM) mount.

Part Number (“y”) indicates cable length and is offered in 3, 5, or 7 meters.

Safety constraints in high voltage systems require the cable shields be bonded to earth
and that the antenna signal lines be inductively earthed such that 50/60Hz signals are not
induced from the high voltage systems.

Содержание 400.00152.0001



















Результаты поиска

Содержание 400.00152.0001

Отзывы:

Похожие инструкции для 400.00152.0001

Бренды по названию

Популярные бренды

IntelliSAW 400.00152.0001, Руководство по интеграции

Результаты поиска

Содержание 400.00152.0001

Отзывы:

Похожие инструкции для 400.00152.0001

Бренды по названию

Популярные бренды