Intellinet 524490 Скачать руководство пользователя | Manualshive

Страница: 110 / 127

background image

The information shown may vary from the output on your screen.

In case you experience technical difficulties with the Router and need to
contact technical support, you should write down the BOOT CODE
Version and RUNTIME CODE version shown on the screen. It is very
likely that you would be asked to provide these numbers by the technical
support representative.

3-4-2 Internet Connection Status

Click the 'Internet Connection' menu on the left of the Web management
interface and the screen below appears:

The information shown may vary from the output on your screen.

This screen shows which IP address information the router has obtained.
If you experience problems with your Internet connection, you should
open this page and check the contents. Values for IP Address, Default
Gateway and Primary DNS should always be filled. If they are missing,
this indicates that there is a connection problem preventing the router
from accessing the Internet.

3-4-3 Device Status

Click the 'Device Status' link on the left of the Web management interface
to view information about the router status:
You can see information about the wireless configuration as well as the
LAN configuration, including information about the encryption and IP
address settings of the router.

«
...
108
109
110
111
112
...
»

Содержание 524490
































































































































Отзывы:

Нет отзывов

Похожие инструкции для 524490

Бренд: 2N Страницы: 3

Бренд: Fortinet Страницы: 11

JBL ENDURANCE PEAK3

Бренд: Harman Страницы: 33

Бренд: Cerio Страницы: 53

Бренд: MeshLinx Страницы: 94

Бренд: Ebyte Страницы: 26

Бренд: Sparklan Страницы: 9

Бренд: Linksys Страницы: 44

Бренд: Loopcomm Страницы: 68

Бренд: Laird Страницы: 10

Бренд: Pioneer Страницы: 3

Бренд: Pioneer Страницы: 6

Бренд: Pioneer Страницы: 9

Бренд: Pioneer Страницы: 12

Бренд: Pioneer Страницы: 132

Бренд: ADDON Страницы: 8

Бренд: EnGenius Страницы: 20

Бренд: AmbiCom Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды